DeWalt DCMWSP660 handleiding

Niet gecategoriseerd

DeWalt

228 pagina's

PDF beschikbaar

Handleiding

/ 228

Je bekijkt pagina 58 van 228

EnGLIsh

TROUBLESHOOTING GUIDE



DANGER: To reduce the risk of serious personal injury, turn unit off, remove safety key, and remove battery pack(s) before making

any adjustments or removing/installing attachments or accessories. An accidental start-up can causeinjury.

For assistance with your product call your local DEWALT authorised servicecentre.

PROBLEM SOLUTION

Mower doesn’t run when bail

handle isactivated

Check to make sure safety key has been installed and is fully seated and that power button has beenpressed.

Release bail handle. Turn mower off. Remove safety key and battery pack(s). Turn mower over and check that the blades turnfreely.

Check that the battery cavity is free of debris and is connectedproperly.

Has battery been fully charged? Press state of chargebutton.

Are both battery packs installed in the mower? Verify battery switch is pointing to one of the battery packs.

Is only one battery pack installed in the mower? Verify battery switch is pointing to installed battery pack.

If the handle folding indicator

is illuminated refer to the Raise the Single Touch Handle section inthismanual.

Blade motor stops

whilemowing

Release bail handle. Turn mower off. Remove safety key and battery pack(s). Turn mower over and check that the blades turnfreely.

Raise cutting height of wheels to highest position and startmower.

Check that the battery cavity is free ofdebris.

Has battery been fully charged? Press state of chargebutton.

Avoid overloading the mower. Slow down the cutting pace, or raise the cutheight.

If the overheat indicator

is illuminated allow the battery and mower to cool down. When cooled, restart the mower and resume

cutting with the mower deck sethigher.

The single touch handle

1

will not lock into the

storageposition

Ensure the two storage latches

at the bottom of the single touch handle

1

tubes pop outward before lowering the single touch

handle

1

into the storageposition.

The main handle

must fully engage the handle windows

. If they are not engaged as shown in Fig. G, press the main

handle

4

towards the handle support

until two audible clicks areheard and both sides of handle windows

are closed as

shown in Fig.H.

Self drive motor stops

whileworking

Shut down power to the self drivingmower.

Clean the self drive motor housing ofdebris.

Check that the wheels are spinningfreely.

Mower runs but

cutting performance is

unsatisfactory, or does not

cut entirelawn

Has battery been fully charged? Press state of chargebutton.

Release bail handle to turn mower off. Remove safety key and battery pack(s). Turn mower over and check:

• Blades for sharpness ‑ Keep bladessharp.

• Deck and discharge chute forclogging.

Wheel height adjustment may be set too low for grass condition. Raise cuttingheight.

Mower is too hard topush Release bail handle to turn mower off. Remove safety key and battery pack(s). Raise cutting height to reduce deck drag on grass.

Check each wheel for freerotation.

If the overheat indicator

is illuminated allow the battery and mower to cool down. When cooled, restart the mower and resume

cutting with the mower deck sethigher.

Mower is abnormally noisy

andvibrates

Release bail handle to turn mower off. Remove safety key and battery pack(s). Turn mower on side and check blade to ensure it

has not been bent or damaged. If blade is damaged, replace with a DeWALT replacement blade. If the underside of the deck is

damaged, return mower to a DeWALT authorised servicecentre.

If there is no visible damage to the blade and the mower still vibrates: Release bail handle to turn mower off. Remove safety key

and battery pack(s). Disassemble entire blade assembly as described in the Removing and Installing Blades section. Remove

any debris and clean each piece. Replace each piece as described in the Removing and Installing Blades section. If mower still

vibrates, return the mower to an authorised DeWALT servicecentre.

Mower not picking up

clippings withbag

Chute clogged. Release bail handle to turn mower off. Remove safety key and battery pack(s). Clear chute of grassclippings.

Raise cutting height of wheels to shorten length of thecut.

Bag full. Empty bag moreoften.

/ 228

Bekijk gratis de handleiding van DeWalt DCMWSP660, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.