Denon DJ DN-M2300R handleiding
Handleiding
Je bekijkt pagina 16 van 38
16
ENGLISH
1) Detection of soundless section
q Make the following two presettings:
• Set “Auto Inc OFF” (3) to “Auto Inc Det.”
• Set the soundless detection level setting to “Inc. Det.-
(48) dB” (4).
w Start playback and recording in such a way that the
beginning of the sound is not missed. When a soundless
section (or a section with level lower than the preset
soundless detection level setting) of at least 2 continuous
seconds is detected, the disc’s track number is
automatically incremented.
(11) Incrementing Track Numbers (MD 2 Only)
During recording, track numbers can be incremented either
manually or automatically.
• Track numbers can be incremented manually in the following
four ways:
1) Press the REC button (
4) during recording. This increments
the track number.
2) Press the PLAY/PAUSE button (
13) during recording to
stop recording for that track number and set the recording
pause mode. When the PLAY/PAUSE button (
13) is
pressed again, recording starts with a new track number.
3) After recording, use the divide function.
• Track numbers can be incremented automatically in the
following three ways, according to the type of input signal:
Input type Method
Detection of soundless section 1)
Detection of soundless section 1)
Using the CD’s or MD’s subcodes 2)
Detection of soundless section 1)
Using the DAT’s start IDs 3)
Analog/digital input
Digital input
CDs
and
MDs
DATs
2 seconds or more
Track number is incrementedSoundless section
NOTE: The auto track increment function may not work when
recording analog signals containing much noise. In this case
lower the detection level to for example –54 dB.
2) Using the CD’s or MD’s subcodes (digital input)
q Make the following presetting:
• Set “Auto Inc OFF” (3) to “Auto Inc Dig.”
w Start playback on the CD (MD) player and recording on the
recorder in such a way that the beginning of the sound is
not missed. The disc’s track number is automatically
incremented when the CD’s (MD’s) track number changes.
Changes in the CD’s (MD’s) track number will not be
detected for approximately 4 seconds after the track
number is incremented.
NOTE:
The auto track increment function using the DAT’s start ID or the CD’s sub codes will not work if the digital input is in professional format
(AES/EBU). Input digital signals of the consumer format (SPDIF).
CD/MD
MD
1
2
3
12345
Copy
Track
number
Track A Track B Track X Track Y Track Z
Previously recorded
tracks
Tracks recorded from
the CD (MD)
Start of recording
Start of recording End of recording
Track X Track Y Track Z
Track
number
DAT
MD
1
2
3
12345
Copy
Track
number
Track A Track B Track X Track Y Track Z
Previously recorded
tracks
Tracks recorded
from the DAT
Start of recording
Start of recording End of recording
Track X Track Y Track Z
Track
number
3) Using the DAT’s start IDs (digital input)
q Record the start ID on the recorded DAT.
w Make the following presetting:
• Set “Auto Inc OFF” (3) to “Auto Inc Dig.”
e Start playback on the DAT player and recording on the
recorder in such a way that the beginning of the sound is
not missed. The disc’s track number is automatically
incremented when the DAT’s start ID is detected. The start
ID will not be detected for 15 seconds after the track
number is incremented.
(12) Pre-UTOC Function (MD 2 Only)
• Presetting must be set.
This function protects the recording should the power supply be
cut off. The UTOC is written directly after recording starts.
(The pre-UTOC is written.)
Normally the UTOC is written after recording is completed, so if
the power supply should be cut off during the recording or
directly after the recording is finished, the recording will not be
registered on the disc. To prevent this, the pre-UTOC (*1) is
registered on the disc directly after recording starts. Once
recording is completed normally, the actual UTOC (*2) is written.
If the power should be cut before the actual UTOC is written, the
disc can be played according to the pre-UTOC. This way you
never accidentally lose recordings that cannot be made over
again.
01Tr 02Tr 03Tr
01Tr 02Tr 03Tr
Pre-UTOC (*1)
Entire disc
Start of recording
End of recording
UTOC (*2)
If some problem occurs and recording is interrupted, the same
recording and UTOC can be written using the following editing
operation:
Use the divide function at the point where recording was
interrupted in track 03 on the above diagram to divide the track,
then use the erase function to erase track 04.
Input signal
Bekijk gratis de handleiding van Denon DJ DN-M2300R, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Denon DJ |
| Model | DN-M2300R |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 5433 MB |
