Handleiding
Je bekijkt pagina 11 van 16
Page 11
When the fast-freezing function is active, the
Freezer temperature is not subject to change
when operating the Freezer zone key for the
first time.
2) To enter “Fast Freezing”.
Press and hold the Care+ key for 3 seconds
when Function setting mode is active. Press
care+ key (short press) , the Fast Freezing
icon will flicker, then press the “OK” key to
activate the function or wait for 5 seconds
until the “Fast Freezing” icon stays On.
3) To exit “Fast Freezing”.
After a cumulative running period of 26
hours, the fast-freezing function will exit
automatically.
When the Fast Freezing function is active,
press and hold Care+ key for 3 seconds to
enter function mode, press Care+ key (short
press) until the icon of Fast Freezing starts
to flickeri, then press the “OK” key or wait for
5 seconds to validate the setting, the “Fast
Freezing” will go off.
When the ECO function is enabled, the ‘Fast
Freezing’ function is automatically disabled.
Alternatively, Quick press the Freezer key
twice to exit the Fast Freezing mode.
Door open alarm
If any door is opened for more than 3
minutes, the buzzer alarm will continuously
beep. It can be stopped by pressing
any key, however will reactivate after 3
minutes if the door is continually opened.
The alarm will stop when the doors are
properly closed.
Power cut memory
In the case of a power failure, the refrigerator
will maintain the last used setting when the
power supply is restored.
Power-on delay
In order to protect the compressor from
being damaged in the case of a short power
failure (i.e., less than 5 minutes), the
compressor will not star up immediately after
it is powered on. It will restart after power
comes back on for more than 5 minutes.
Over-temperature alarm (only after power
outage)
When the refrigerator system is powered on,
if the freezer sensor temperature is higher
than -10°C, the freezer zone display digits
will flicker. The freezer temperature will be
displayed when any key is pressed. The
normal display will be restored when any key
is pressed again or after 10 seconds.
Fault alarm
In case E0, E1, E2, EH,EE or EC is
displayed on the display panel, it indicates
fault with the refrigerator. Please contact
the customer care line for assistance should
any of the above error messages display.
Turn off the flip beam heater manually
Press and hold down the “Variable” and
“Fridge” key for 3s to enter the “Special
Program Working State” setting program,
with the character “Sd” flickering on the
display, and 2 seconds later, the current
setting of the “Special Program” will be
displayed; Then, press the “Fridge”/
“Freezer” key to switch the setting to On,
with the character “on” displayed; The said
setting will be memorized if no key operation
within 5 seconds, the current program will
stop and the normal program will resume.
Press the “Fridge” key for more than 3
seconds while holding down the “Care+” key
to enter the flip beam heater On/Off setting
program, which is on by default. “on” is
displayed; Then you can press the “Fridge”
key to switch the setting between 1 (On) and
0 (Off). When the flip beam heater is set to
"Off", the anti-condensation function is
disabled, with the flip beam heater turned off.
This function will not be memorized, and the
flip beam heater is in the on state when the
system is powered on again.
Note: Do not access this setting during use,
as it is only used for testing and verification
purposes.
Bekijk gratis de handleiding van Defy DFF590, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Defy |
| Model | DFF590 |
| Categorie | Vriezer |
| Taal | Nederlands |
| Grootte | 1939 MB |
