Dedra DED7075 handleiding
Handleiding
Je bekijkt pagina 5 van 31
5
Li-Ion battery and charger are not included in the purchased device and must be
purchased separately. The use of batteries and chargers other than those
dedicated to the device is prohibited.
2. Description of the device
Fig. A. 1. clamp, 2. battery socket, 3. on/off switch, 4. suction opening, 5. blowout
opening, 6. wide nozzle, 7. crevice nozzle, 8. flexible hose, 9. hose holder,
DED7174 only: 10. battery status indicator
Fig. B. 11. HEPA-type washable filter, 12. Filter locking knobs, 13. Water overflow
protection
3. Purpose of the device
Bagless vacuum cleaner, is designed for dry or wet vacuuming (for water
extraction). The device can also be used as a blower, after connecting a flexible
hose to the air outlet on the back of the device.
It is permissible to use the device in repair and construction work, repair workshops,
in amateur work while observing the conditions of use and permissible working
conditions contained in the instruction manual.
4. Restrictions on use
The device may only be used in accordance with the
"Permissible Operating Conditions" below.
The vacuum cleaner must not be used for extraction of excavated material during
sanding work (wood, plastics, metals, gypsum surfaces, building materials, etc.)
The vacuum cleaner must not act as a pump.
Unauthorized changes to the mechanical and electrical
structure, any modifications, maintenance activities not
described in the Operation Manual will be considered illegal and cause
immediate loss of Warranty Rights, and the Declaration of Conformity will
lose its validity. Use of the device contrary to its intended use or the
Operating Instructions will result in immediate loss of Warranty Rights.
ACCEPTABLE WORKING CONDITIONS
Use only indoors. Battery charging temperature range 10 - 30°C. Do not
expose to temperatures above 40°C. Protect from moisture and
precipitation
5. Technical data
Device model
DED7075
DED7174
Operating voltage [V].
18 d.c.
18 d.c.
Engine type
Brush
Brushless
Vacuum [kPa].
9
15
Tank capacity [l].
10
10
IP degree of protection
IP24
IP24
Weight [kg].
3,1
3,1
6. Preparation for work
The device is part of the SAS+ALL line, so in order to use
it, you must complete a set, consisting of the device,
battery and charger. The use of other batteries and chargers is prohibited.
The preparatory steps described below should be
performed with the power source disconnected.
Before the first use, unfasten the safety clamps (fig. A, 1) and remove all
components from the tank. Check that the HEPA-type filter (fig. B, 11) is correctly
inserted and its locking knobs (fig. B, 12) are tightened. Check that the tank's water
overflow protection (fig. B, 13) is free of dirt, clogging, etc. Connect the flexible hose
(fig. A, 3) to the suction opening (fig. A, 8) so that the hose latch fits into the suction
opening (it should be facing up). Underneath the tank there are tip compartments
(Fig. A, 6, 7). Select the appropriate tip for the job and put it on the flexible hose.
Place the battery from the SAS+ALL line in the socket (Fig. A, 2). The device is
ready for operation.
7. Turning on the device
The device is powered by an 18V battery.
Slide the charged battery into the guide until the handle latch engages. The device
is ready for operation. Turn on the device with the switch (Fig. A, 3).
DED7174 only: The switch (Fig. A, 3) has 2 positions: "I" corresponds to operation
with reduced suction power, "II" is for operation with full power.
8. Use of the device
Holding the end of the flexible hose or the selected accessory, vacuum the selected
surfaces, avoiding blocking the airflow (clogging the working end). Avoid excessive
twisting and bending of the flexible hose. Adjust the working tip to the surface to be
cleaned. Use the extension cord supplied with the device to improve working
comfort.
Dry work
The vacuum cleaner is a bagless device, the dirt from the vacuumed surface
collects directly in the tank.
Wet work
During wet operation, regularly check the water level in the vacuum cleaner tank,
empty it regularly. If during wet operation the water level in the tank is too high and
the water seizes the ends of the water level protection (Fig. B, 13), the vacuum
cleaner will turn off automatically. Before resuming work in such a case, rinse the
filter (Fig. B, 11), dry it thoroughly and only then resume operation of the device.
Do not allow operation with a wet filter!
Blowdown operation
Make sure that the vacuum cleaner tank is empty and the filter is clean. Insert the
flexible hose (Figure A, 8) into the blowout hole (Figure A, 5). Turn on the vacuum
cleaner and point the end of the flexible hose in the desired direction.
9. Ongoing maintenance
Maintenance and cleaning of the vacuum cleaner
Regularly clean the entire device, paying special attention to cleaning the ventilation
holes of the device .
After each use, empty the vacuum cleaner tank, clean it and dry it thoroughly (if it
was used for wet work). Remove and clean the HEPA type filter. To do this, use a
fine, soft brush with which to pre-clean the HEPA-type filter. Then wash it under
cold running water (rinse, do not use detergents, solvents, etc.).
Filter cleaning
Unfasten the clamps (fig. A, 1) and remove the top cover of the vacuum cleaner.
Turn the 4 filter locking knobs (fig. B, 12) a quarter turn counterclockwise. Remove
the filter (Fig. B, 11) and rinse under cold running water. Do not use detergents,
solvents, etc. Before reattaching the filter, allow it to dry freely at room temperature.
For drying, do not use tanning machines, dryers, heaters, heaters, etc. Put the dried
filter back on, and turn the lock knobs a quarter turn clockwise.
The storage area of the device should be inaccessible to
children.
If you need to send the device to a service center for repair, protect it from
accidental mechanical damage and remove the batteries from the charger socket.
Never carry out maintenance work on a device connected
to a power source.
Slide the battery out of the device's socket before performing maintenance.
Maintenance of the device consists in keeping all its components necessary for
normal operation clean. Do not use any solvents for cleaning as this may cause
irreparable damage to the housing and other elements made of plastic.
Battery maintenance
Avoid charging the battery immediately after heavy use. Due to the characteristics
of the battery, do not store it completely discharged, as it may then discharge below
a critical level and become permanently damaged.
The battery must not be cleaned with water as this may cause an internal short
circuit leading to permanent damage.
So store the battery when not in use, partially charged (up to about 40%). Recharge
the battery before it is completely discharged. Store batteries at temperatures of
10-30°C. Stored at low temperatures, it loses capacity faster.
Battery charging is described in the instructions for the battery and charger from
the SAS+ALL line.
How to remove the battery
To remove the battery, press the release button on the front of the battery. Slide
the battery out of the socket. To install the battery pack, slide the battery pack into
the slot and then press down until the handle latch engages.
After each use
- Remove the battery pack from the socket to avoid accidental activation by
bystanders or during handling. Store the device with the battery disconnected.
Storage and transportation
When the device is not in use, store it unplugged from the power source, out of the
reach of children, in a dry and ventilated place. Transport the device and other
components listed in the set as far as possible in the original packaging, in a way
that does not expose them to harmful environmental conditions such as humidity,
precipitation, high temperature (above 40°C), pressure that may result in
mechanical damage and others that may adversely affect the package or its
contents.
10. Spare parts and accessories
Recommended accessories
The SAS+ALL line can be equipped with any battery and charger from the
SAS+ALL line.
To purchase spare parts and accessories, contact Dedra Exim service. Contact
information is on the 1st page of the manual.
When ordering spare parts, please quote the lot number on the nameplate and the
part number from the assembly drawing.
During the warranty period, repairs are carried out under the terms of the warranty
card. Please hand over the claimed product for repair at the place of purchase (the
seller is obliged to accept the claimed product), send it to the Dedra Exim central
service center or send it to the service center closest to your place of residence (list
of service centers at www.dedra.pl). Kindly include the completed warranty card.
After the warranty period, repairs are performed by the central service. Send the
defective product to the service center (shipping costs are paid by the user).
11. Troubleshooting on its own
Unplug the device from the power supply before
performing any troubleshooting yourself.
PROBLEM
CAUSE
SOLUTION
Vacuum cleaner
doesn't work
Defective switch
Discharged battery
Badly installed battery
Take the device to a
service center
Charge the battery
Fix correctly
Vacuum cleaner
works with difficulty
Discharged battery
Charge the battery
properly
Bekijk gratis de handleiding van Dedra DED7075, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Dedra |
| Model | DED7075 |
| Categorie | Stofzuiger |
| Taal | Nederlands |
| Grootte | 8867 MB |
