Dedra DED70093 handleiding
Handleiding
Je bekijkt pagina 6 van 29
6
8. Masz prawo wniesienia skargi do wniesienia skargi do organu właściwego do
spraw ochrony danych osobowych.
EN Table of contents
1. Drawing and pictures
2. Description of the device
3. Purpose of the device
4. Restriction on use
5. Technical data
6. Preparing for use
7. Switching on the device
8. Operation of the device
9. Ongoing maintenance
10. Spare parts and accessories
11. Trouble-shooting on your own
12. Contents of the package
13. Information for users on the disposal of electrical and electronic equipment
(applicable to households)
14. Warranty card
The traslatination of the oryginal manual
The Declaration of Conformity is attached to the manual as a separate document.
If the Declaration of Conformity is not available, please contact Dedra Exim.
General safety regulations are attached to the manual as a separate booklet.
WARNING. Read all warnings marked with the symbol and all
instructions.
Failure to observe the following warnings and safety instructions could result in
electric shock, fire or serious injury.
Retain all warnings and instructions for future use.
The SAS+ALL series is designed to work exclusively with
SAS+ALL series chargers and batteries.
The battery and charger are not included in the equipment purchased and must be
purchased separately. It is prohibited to use batteries and chargers other than those
intended for this equipment.
2. Description of the device
Fig. A: 1 - power tool socket, 2 - angle adjustment button, 3 - latches. 4 - telescopic
tube, 5 - battery socket, 6 - switch, 7 - safety switch
3. Purpose of the device
The telescopic jib is designed to attach and work with DED7177, DED6984,
DED7179, DED7980, DED7181S power tools from the SAS+ALL line. Using the jib
significantly increases the working range of power tools, allowing you to work within
the reach of the jib (max. 270 cm) in hard-to-reach places (at height or horizontally,
at a distance inaccessible without the jib).
It is permissible to use the device in renovation and construction work, repair
workshops, amateur work, subject to the conditions of use and permissible working
conditions contained in the operating instructions.
4. Restriction on use
The appliance may only be used in accordance with the
‘Permitted operating conditions’ below.
Use only with power tools DED7177, DED6984, DED7179, DED7980, DED7181S
of the SAS+ALL series.
Unauthorised changes to the mechanical and electrical
design, any modifications, maintenance operations not
described in the operating instructions will be treated as illegal and will result
in the immediate loss of warranty rights and the declaration of conformity will
become invalid.
Misuse or use not in accordance with the operating instructions will result in
immediate loss of warranty rights.
Permitted operating conditions’
Battery charging temperature range 10 - 30°C. Do not expose to
temperatures above 40°C.
5. Technical data
Model type
DED70093
Rated voltage [V]
18 d.c.
Range [cm]
140 – 270
Weight [kg]
1,55
6. Preparing for use
The device is part of the SAS+ALL line, so to use it, a kit
consisting of the device, battery and charger must be
completed. The use of other batteries and chargers is prohibited.
All operations described in this chapter should be carried
out with the battery disconnected.
Remove boom from packaging, check for visible mechanical damage.
Do not use a damaged boom.
Adjusting the length of the boom
To adjust the length of the boom, release the catches (Fig. A, 3), extend or retract
the telescopic tube as required. Tighten the latches, ensure that the telescopic
rivulets are locked.
Inserting the power tool and battery pack
Fit the power tool of your choice into the power tool attachment slot (Fig. A, 1).
Use only for power tools DED7177, DED6984, DED7179, DED7980, DED7181S
of the SAS+ALL line.
Insert any battery pack from the SAS+ALL line into the battery pack socket (Fig. A,
5).
Adjusting the tilt of the power tool
Press the button (Fig. A, 2) and change the angle of the power tool socket. Release
the button, thus locking the angle of the tilt.
A shoulder strap can be used to make work easier. The belt can be fitted to the
telescopic eye rings on the tubes.
7. Switching on the device
Przed uruchomieniem urządzenia bezwzględnie wykonać
czynności opisane w rozdziale „Przygotowanie do pracy”.
The handle of the appliance has an on/off switch (Fig. A, 6) and a button to prevent
accidental switching on (Fig. A, 7). To switch on the appliance, press the safety
switch button and then press the switch button. The power tool will continue to
operate until the switch button is released.
8. Operation of the device
If the battery gets hotter than 40°C, stop operation and
wait for the battery to cool down.
When operating the device, all safety rules and
instructions described in the safety conditions must be
strictly observed..
Start working after connecting the battery and the power tool. Always hold the
extension arm with both hands, with your right hand on the main handle with the
switch and your left hand on the EVA-covered part of the telescopic tube. Make
sure you are in a stable position.
Carry out the work depending on the connected power tool (secateurs DED7177 or
chain saws DED6984, DED7179, DED7980, DED7181S from the SAS+ALL line
according to the instructions in the manual for the selected power tool).
After finishing work, release the switch lock button, disconnect the power tool and
the battery.
9. Ongoing maintenance
All maintenance must be carried out with the unit
unplugged.
Avoid charging the battery pack immediately after intensive use. Due to the
discharge phenomenon, do not store the battery pack completely discharged, as it
may then discharge below a critical level and become permanently damaged.
Therefore, when not in use, the battery should be stored partially charged (to
approx. 40%). The battery should be charged before it is completely discharged.
Batteries should be stored at a temperature of 10-30°C. Batteries stored at low
temperatures lose capacity more quickly.
For how to charge the battery pack, refer to the instructions for the battery pack and
charger in the SAS+ALL series.
Keep the device out of the reach of children.
If it is necessary to send the device to a service centre for
repair, protect it from accidental mechanical damage and remove the batteries from
the charger socket.
How to dismantle the battery
To remove the battery pack, grasp the unit by the handle and then press the release
button on the front of the battery pack. Slide the battery pack out of the socket. To
fit the battery pack, slide the battery pack into the battery slot and then press down
until the handle latch engages.
Attachment, tool replacement
Once the tool has been clamped, make sure it has been clamped correctly: lay the
power tool horizontally and try to eject the clamped tip. If it cannot be ejected, it
means that it has been clamped correctly.
Maintenance of the appliance
Maintenance includes servicing of the equipment including accessories, i.e. the
battery and charger..
Never carry out maintenance work on equipment that is
connected to a power source.
This can cause serious injury or electric shock. The battery must be removed from
the battery socket before maintenance.
Maintenance of the unit consists of keeping all its components necessary for normal
operation properly clean. No solvents may be used for cleaning as this may cause
irreparable damage to the casing and other plastic components.
The battery must not be cleaned with water as this may cause internal short circuits
leading to permanent damage.
Before each start-up:
- Check that the engine vents are not obstructed or dirty. If necessary, expose/clean
with a cloth slightly dampened with water.;
After each use:
- Disconnect the battery to avoid accidental activation by unauthorised persons or
during handling.
10. Spare parts and accessories
For the purchase of spare parts and accessories, please contact the Dedra Exim
service. Contact details can be found on page 1 of the manual.
When ordering spare parts, please quote the batch number on the nameplate
together with the part number from the assembly drawing.
During the warranty period, repairs are carried out in accordance with the terms of
the warranty card. Return the faulty product for repair at the place of purchase (the
dealer is obliged to accept the faulty product), send it to the central Dedra Exim
service centre or to the service centre closest to your place of residence (list of
service centres at www.dedra.pl). Kindly enclose the completed warranty card. After
Bekijk gratis de handleiding van Dedra DED70093, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Dedra |
| Model | DED70093 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 7335 MB |
