Dali Phantom CI AMP-4750 DSP handleiding
Handleiding
Je bekijkt pagina 15 van 16
Diagram8M
Amplifier Signal Flow Schematic
8.6 Setup and Signal Routing
Thanks to the DALI PHANTOM CI AMP
CONFIGURATOR the AMP-4750 DSP amplifier oers
considerable versatili in terms of sources, signal
routing, installation zones and output modes. Inputs can
be freely assigned to installation zones, and those zones
assigned freely to the available amplifier outputs in either
Lo-Z or Hi-Z modes.
This versatili enables, for example, dierent inputs to be
routed to dierent output zones.
The following paragraphs describe and illustrate the
recommended procedure for configuring input, zone and
output routing. A general signal flow schematic is also
illustrated in Diagram8M.
8.7 Input Setup
Open the configuration Dashboard and select the [Input]
tab. The [Input] tab is shown in Diagram8B.
• To edit default input names simply select and pe in the
Input Name field.
• Define a mono or stereo input by selecting the
appropriate option. Defining a stereo input will reduce
the total number of discrete inputs available.
• Select an input sensitivi option from the [Sensitivi]
drop-down menu: +14dB, +4dB, -10dB and
“[Microphone]” options are available. Generally,
the +14dB or +4dB options are appropriate for
“professional audio” source hardware with balanced
outputs, while the -10dB option is more appropriate
for “consumer audio” source hardware with
unbalanced outputs. The [Microphone] option provides
the significantly greater sensitivi required for
microphones.
NOTE
Only dynamic microphones are suitable for connection.
Phantom power for condenser microphones is not
provided.
• If necessary, adjust the input gain using the slider or
up/down icons. Gain adjustment is intended to be used
for fine output level adjustment following initial use.
8.8 Zone Setup & Routing
Open the configuration Dashboard and select the [Zone]
tab. The [Zone] tab is shown in Diagram8E.
• Select the zone to be configured. The number of zones
available and their channel format (stereo or mono) will
depend on the amplifier input setup and output mode
(Lo-Z or Hi-Z). For example, a four output amplifier can
have the following zone configurations:
• 2 × stereo Lo-Z zone
• 4 × mono Lo-Z zones
• 2 × mono Hi-Z zone
• 2 × mono Lo-Z BTL zone
• Name zones by ping in the Zone Name field.
• Adjust the zone volume if required by using the slider.
• Define a mono or stereo zone by selecting the
appropriate option. Defining a stereo zone will reduce
the total number of further zones available.
• Speci an input for the zone by selecting from the
drop-down menu. Selecting a stereo input for a mono
zone will automatically sum the stereo channels to
mono.
NOTES
When configured in Lo-Z BTL mode or Hi-Z mode, the
AMP-4750 DSP amplifier operates in “bridged” mode
where the output of two channels is combined. This
means that the number of output channels available in
these modes is half that available in Lo-Z mode.
Mono signals might be mono at source, created though
combining the le and right channels of a stereo signal
(summed mono) or treating the le and right channels of
a stereo signal independently (split mono).
Analogue 3
Output
Matrix
Zones A - D
Outputs 1 - 4
Analogue 2
Input
Sensitivi
Analogue 1
Input
Gain
Input
Sensitivi
Input
Gain
Input
Sensitivi
Input
Gain
Analogue 4
SPDIF (stereo)
SPDIF Out.
(stereo - any two input or zone signals)
Pink Noise
Gain
Level
Adjustment
Level
Adjustment
Compressor
Compressor
Delay
Delay
EQ
EQ
EQ
EQ
FIR
FIR
BTL
Amplifier
2 x Low-Z
1 x Hi-Z
Limiter
Polari
Polari
Polari
Polari
Limiter
Driver
Alignment
Driver
Alignment
Crossover
Crossover
Gain Trim
Gain Trim
Input
Sensitivi
Input
Gain
Input
Gain
Input
Selection
Input Setup
Zone Setup
& Routing
Output Setup
Output 1
Output 2
Level
Adjustment
Level
Adjustment
Compressor
Compressor
Delay
Delay
EQ
EQ
EQ
EQ
FIR
FIR
BTL
Amplifier
2 x Low-Z
1 x Hi-Z
Limiter
Limiter
Driver
Alignment
Driver
Alignment
Crossover
Crossover
Gain Trim
Gain Trim
Output 3
Output 4
Zone Adjustment
Parameters
Speaker Preset Parameters
28 29
Bekijk gratis de handleiding van Dali Phantom CI AMP-4750 DSP, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Dali |
| Model | Phantom CI AMP-4750 DSP |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 3633 MB |