Daikin EPVX14SU23A handleiding
Handleiding
Je bekijkt pagina 15 van 20
6 Energy saving tips
Operation manual
15
EPVX10+14S(U)18+23A + EPBX10~14A
Daikin Altherma 4 H F+W
4P773378-1 – 2024.11
5.9.2 Using weather-dependent curves
Related screens
The following table describes:
▪ Where you can define the different weather-dependent curves
▪ When the curve is used (restriction)
To define the curve, go to… Curve is used when…
[1.8] Main zone > Heating WD
curve
[1.5] Heating setpoint mode =
Weather dependent
[1.9] Main zone > Cooling WD
curve
[1.7] Cooling setpoint mode =
Weather dependent
[2.8] Additional zone >
Heating WD curve
[2.5] Heating setpoint mode =
Weather dependent
[2.9] Additional zone >
Cooling WD curve
[2.7] Cooling setpoint mode =
Weather dependent
INFORMATION
Maximum and minimum setpoints
You cannot configure the curve with temperatures that are
higher or lower than the set maximum and minimum
setpoints for that zone. When the maximum or minimum
setpoint is reached, the curve flattens out.
To define a weather-dependent curve
Define the weather-dependent curve using two setpoints (b, c).
Example:
35.0°
max
–15.0°
25.0°
b
a
Y
X
c
d
e f
35.0°
15°
–15.0°
min
0°
WDC Main zone
Outside temperature
Outside temperature
LWT
LWT
Item Description
a Selected weather-dependent curve:
▪ [1.8] Main zone – Heating ( )
▪ [1.9] Main zone – Cooling ( )
▪ [2.8] Additional zone – Heating ( )
▪ [2.9] Additional zone – Cooling ( )
b, c Setpoint 1 and setpoint 2. You can change them:
▪ By dragging the setpoint.
▪ By tapping the setpoint, and then using the – / +
buttons in e, f.
Item Description
d Increase around 0°C (same as setting [1.26] for main
zone, and [2.20] for additional zone).
Use this setting to compensate for possible heat losses
of the building due to the evaporation of melted ice or
snow. (e.g. in cold region countries). In heating
operation, the desired leaving water temperature is
locally increased around an outdoor temperature of 0°C.
X
Y
R
L
0°C
L: Increase; R: Span; X: Outdoor temperature; Y:
Leaving water temperature
Possible values:
▪ No
▪ increase 2°C, span 4°C
▪ increase 2°C, span 8°C
▪ increase 4°C, span 4°C
▪ increase 4°C, span 8°C
e, f Values of the selected setpoint. You can change the
values using the – / + buttons.
X-axis Outdoor temperature.
Y-axis Leaving water temperature for the selected zone.
The icon corresponds to the heat emitter for that zone:
▪ : Underfloor heating
▪ : Fan coil unit
▪ : Radiator
To fine-tune a weather-dependent curve
The following table describes how to fine-tune the weather-
dependent curve of a zone:
You feel… Fine-tune with
setpoints:
At regular outdoor
temperatures …
At cold outdoor
temperatures …
Setpoint 1
(b)
Setpoint 2
(c)
X Y X Y
OK Cold ↑ ↑ — —
OK Hot ↓ ↓ — —
Cold OK — — ↑ ↑
Cold Cold ↑ ↑ ↑ ↑
Cold Hot ↓ ↓ ↑ ↑
Hot OK — — ↓ ↓
Hot Cold ↑ ↑ ↓ ↓
Hot Hot ↓ ↓ ↓ ↓
6 Energy saving tips
Tips about room temperature
▪ Make sure the desired room temperature is NEVER too high (in
heating mode) or too low (in cooling mode), but ALWAYS
according to your actual needs. Each saved degree can save up
to 6% of heating/cooling costs.
▪ Do NOT increase/decrease the desired room temperature to
speed up space heating/cooling. The space will NOT heat up/cool
down faster.
Bekijk gratis de handleiding van Daikin EPVX14SU23A, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Daikin |
| Model | EPVX14SU23A |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 3173 MB |
