Daikin DTA114A61 handleiding

Niet gecategoriseerd

Daikin

2 pagina's

PDF beschikbaar

Handleiding

Bind the power supply wire for

indoor PCB with the remote

controller wiring and the connection

wiring using clamp material.

1P224646-1A

〈CAUTION〉

Follow the “FIELD SETTING” in the installation manual of the remote controller for the indoor unit and make a necessary field setting in the remote controller after turning the air conditioner ON.

•

Set the remote controller to field set mode, select Mode No. “12”, and set the FIRST CODE NO. to “1” and the SECOND CODE NO. to “04”.

(The SECOND CODE NO. is factory set to “01”.)

Note: The remote control terminals (T1 and T2) of the indoor unit is for multi-tenant use. Therefore, the COMPUTERIZED CONTROL of the indoor unit is not available.

• For connection to the terminal block, be sure to use a ring type crimp style terminal.

Also insulate the crimping portion, for example, by mounting an insulation sleeve.

• For wiring, use the specified wire to connect it securely and fix it so that external force is not applied to the

terminal.

• For tightening the terminal screw, use a proper screwdriver.

A smaller size screwdriver may damage the screw head, resulting in improper tightening.

• If the terminal screw is secured too tightly, the screw may be damaged.

For tightening torque for terminal screw, see the table on the right-hand side.

Ring type crimp style terminal

Wire

Insulation sleeve

Terminal block of adaptor for multi tenant (X1M, X2M) 1.18~1.44

Tightening torque (N · m)

〈In the case of mounting to lid

of installation box for adaptor〉

〈

*Processing procedure for field wiring

〉

Adaptor power supply wire

through relay contact

(24VAC) (*field wiring)

Short-circuited

with electric wire.

Shall be clamped at

sheath portion.

Lid of installation box for adaptor

Adaptor for multi tenant

Power supply

wire for indoor

PCB (accessory)

Shall be clamped

near wiring stop.

〈In the case of mounting to

installation box for adaptor〉

Installation box for adaptor

Shall be clamped at

sheath portion.

Power supply

wire for indoor

PCB (accessory)

Shall be clamped

near wiring stop.

Adaptor power supply

wire through relay

contact (24VAC)

(*field wiring)

Adaptor for multi tenant

Short-circuited

with electric wire.

Power supply wire for adaptor (24VAC),

indoor contact input wire

Drain pump

lead wire

Installation box for adaptor

Power supply wire for indoor

PCB

Float switch lead wire

Bind the adaptor power supply wire (24VAC) and the indoor connection input

wire together with the drain pump lead wire using clamp material.

Be careful about jam at the lid

of electric component box.

Field wiring

Bind the provided power supply

wire for indoor PCB and the field

wiring using clamp material.

Bind the power supply wire for indoor

PCB with the float switch lead wire using

clamp material.

Power supply wire for BS

PCB (accessory)

Carry out wiring to keep it from

contact with electronic parts.

Bind using clamp material.

Adaptor for multi tenant

Adaptor power supply wire through

relay contact

(24VAC) (*field wiring)

(Do not take it for the 200-240VAC wire.)

Power supply wire for BS unit

Clamp it at the sheath portion

with the power supply wire for

BS unit.

FXMQ (Ceiling-mounted Duct Type)

FXFQ (Ceiling-mounted Cassette Round-flow Type)

BSVQ (BS unit)

〈

*Processing procedure for field wiring

〉

〈In the case of mounting to

installation box for adaptor (left)〉

〈In the case of mounting to

installation box for adaptor (right)〉

Short-circuited

with electric wire.

Short-circuited

with electric wire.

Adaptor power supply wire through relay contact

(24VAC) (*field wiring)

Adaptor power supply wire

through relay contact

(24VAC) (*field wiring)

Adaptor for multi

tenant

Power supply

wire for indoor

PCB (accessory)

Installation box for adaptor

Bind using clamp material.

Carry out wiring to keep it

from contact with parts on

the PCB.

Carry out wiring to keep it

from contact with parts on

the PCB.

Installation box for adaptor

Bind using clamp material.

Power supply wire for indoor

PCB (accessory)

Carry out field wiring to

keep it from contact with

parts on the PCB.

〈

*Processing procedure for field wiring

〉

〈

*Processing procedure for field wiring

〉

FXAQ (Wall-mounted type)

Power supply wire for indoor

PCB (accessory)

Adaptor for multi tenant

Power supply wire for indoor

PCB (accessory)

Adaptor power supply wire through relay contact

(24VAC) (*field wiring)

Short-circuited

with electric wire.

50 10 mm

–

50 10 mm

–

60 10 mm

–

50 10 mm

–

Bind using clamp material.

METHOD OF WIRING

FIELD SETTING

Short-circuited

with electric wire.

Bekijk gratis de handleiding van Daikin DTA114A61, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.