D-Link DPS-PWR1200AC handleiding
Handleiding
Je bekijkt pagina 15 van 46
DXS-3130-28-P Layer 3 Stackable Managed Switch Hardware Installation Guide
15
LED status indicator behavior
LED
Description
Power
This LED will light solid green after the Switch has been powered on
successfully.
This LED will be off when the Switch is no longer receiving power (i.e.
powered off).
Console
This LED will light solid green when the console port is active.
This LED will be off when the console port is not active.
MGMT
The LED at the left side indicates the status of MGMT port.
This LED will light solid green (1000 Mbps) or amber (10/100Mbps) after a
link to the MGMT port was successfully established.
This LED will blink when activity on this port is taking place.
This LED will be off when MGMT port is not active.
The LED at the right side has no LED notification.
RPS
This LED will light green when the Redundant Powers Supply is in use.
This LED will be off when the RPS is not in use.
Fan Error
This LED will light solid red when the fan fails.
This LED will be off when the fan is in normal operation.
USB
This LED will light solid green if a USB flash drive is plugged in.
This LED will blink green when the Switch is reading or writing data to and
from the USB drive.
This LED will be off when no USB drive is plugged into the USB port.
Link/Act/Speed LEDs & PoE LEDs
The Switch has LED indicators for Link and Activity.
PoE LED (No. 1~24): The right LEDs of the above ports indicate power
supply status. This LED will light solid green when there is a PoE device
connected to the port and is receiving power from the port. This LED will
light amber to indicate an error state in power supply. The LED is off when
there is no power device connected to the port.
10G RJ45 Ports (No. 1~24): The left LED will light solid green when there
is a connection (or link) to a 2.5/5/10 Gbps Ethernet device; the right LED
will light solid amber when there is a connection (or link) to a 100/1000
Mbps Ethernet device on any of the RJ45 ports. The left LED will blink
green when a 2.5/5/10 Gbps port is active; the right LED will blink amber
when a 100/1000 Mbps port is active. The LED will be off when there is no
link or activity.
SFP28 Ports (N0. 25~28): The triangle LED indicates the Link/Act/Speed
status of 25G SFP28 ports. This LED will light solid green when there is a
connection (or link) to a 25 Gbps Ethernet device or solid amber when
there is a connection (or link) to a 10 Gbps Ethernet device on any of the
SFP28 ports. The LED will blink green when a 25 Gbps port is active or
blink amber when a 10 Gbps port is active. The LED will be off when there
is no link or activity.
Stack ID
This 7-segment LED can display numbers from 1 to 9 and the following
letters H, h, E, and G. The stacking ID (1 to 9) can be assigned manually by
the user or automatically by the system.
The letter ‘H’ will be displayed if this switch is the master switch in the
stack.
The letter ‘h’ will be displayed if this switch is the backup master switch in
the stack.
The letter ‘E’ will be displayed if there was an error in the system’s self-test.
The letter ‘G’ will be displayed when the Safeguard engine entered the
exhausted mode.
Bekijk gratis de handleiding van D-Link DPS-PWR1200AC, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | D-Link |
| Model | DPS-PWR1200AC |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 7634 MB |
