Curtis 1253 handleiding
Handleiding
Je bekijkt pagina 24 van 49
18
Curtis 1253 Manual, Rev. F
3 — PROGRAMMABLE PARAMETERS: Throttle Parameters
deadband to be defined wide enough to ensure that the controller goes into
neutral when the throttle mechanism is released.
Examples of deadband settings (30%, 10%, 0%) are shown in Figure 8
for throttle types 0 through 3, using a nominal 5kΩ–0 potentiometer (where
applicable).
e programmer displays the throttle deadband parameter as a percentage
of the nominal wiper voltage range and is adjustable from 4% to 90%, in 1%
increments. e default deadband setting is 10%. e nominal wiper voltage
range depends on the throttle type selected. See Table 1 (page 11) for the char-
acteristics of your selected throttle type.
THROTTLE MAX
e rottle Max parameter sets the throttle wiper voltage required to produce
100% controller output. Decreasing the throttle max setting reduces the wiper
voltage and therefore the full stroke necessary to produce full controller output.
is feature allows reduced-range throttle assemblies to be accommodated.
Examples are shown in Figure 9 for throttle types 0 through 3, using a
nominal 5kΩ potentiometer (where applicable). ese examples illustrate the
eect of three dierent max output settings (100%, 90%, 60%) on the full-
stroke wiper voltage required to attain 100% controller output.
e programmer displays throttle max as a percentage of the throttle’s
active voltage range. e nominal voltage range depends on the throttle type
selected. See Table 1 (page 11) for the characteristics of your selected throttle
type. e throttle max parameter can be adjusted from 100% to 10%, in 1%
increments.
Notes: Voltages shown are at the pot wiper relative to B-.
For Types 0 and 1, the deadband points are defined in
terms of the nominal 5kΩ pot resistance. Using a pot
of greater or lesser resistance will give different values
for the deadband points.
Throttle Max parameter set at 100%.
0.5V
1.5V
5V
0
4.5V
(5.0kΩ)
30% Deadband
10% Deadband
0% Deadband
4.1V
(4.5kΩ)
3.3V
(3.5kΩ)
0.6V
(0Ω)
0.6V
(0Ω)
0.6V
(0Ω)
KEY
100%
Neutral
Deadband
Controller
Output
0%
5V
0
30% Deadband
10% Deadband
0% Deadband
5V
0
30% Deadband
10% Deadband
0% Deadband
1.0V
(500Ω)
1.8V
(1.5kΩ)
4.5V
(5.0kΩ)
4.5V
(5.0kΩ)
4.5V
(5.0kΩ)
5V
0
30% Deadband
10% Deadband
0% Deadband
5V
0
30% Deadband
10% Deadband
0% Deadband
Throttle Types 2 and 3 (0–5V and 3-wire pot)
Throttle Type 1 (5k
Ω–0)
Throttle Type 0 (0–5k
Ω)
0.6V
(0Ω)
Fig. 8, cont’d Eect of
adjusting the throttle
deadband parameter
(throttle types 2 and 3).
Bekijk gratis de handleiding van Curtis 1253, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Curtis |
| Model | 1253 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 6360 MB |
