Crestron Green Light GL-EXP-SW-CN handleiding

Niet gecategoriseerd

Crestron

2 pagina's

PDF beschikbaar

Handleiding

GL-EXP-DIM-CN/GL-EXP-DIMFDB-CN/GL-EXP-DIMFLV-CN/GL-EXP-DIMU-CN/GL-EXP-SW-CN

Crestron Green Light

Expansion Module with Cresnet

Communication

Installation Guide

Description

The GL-EXP-DIM-CN, GL-EXP-DIMFDB-CN, GL-EXP-DIMFLV-CN, GL-EXP-DIMU-CN,

and GL-EXP-SW-CN are single-channel Crestron Green Light expansion modules that are

controlled with Cresnet communication. They provide control for a variety of lighting loads.

A single module supports 100 to 277 volt loads up to 16 amps.

The Crestron

GL-EXP-DIM-CN, GL-EXP-DIMFDB-CN, GL-EXP-DIMFLV-CN,

GL-EXP-DIMU-CN, and GL-EXP-SW-CN share common features and functions and will be

referred to as “GL-EXP-*-CN” except where noted.

The specications for the GL-EXP-*-CN are listed below.

Specications

SPECIFICATION DETAILS

Load Ratings

Channels

Load Rating

Dimmed Load Types

Switched Load Types

16 A

GL-EXP-DIM-CN:

LED, incandescent, neon/cold cathode, magnetic

low-voltage, 2-wire dimmable uorescent

GL-EXP-DIMU-CN:

Incandescent, LED, electronic low-voltage, magnetic

low-voltage, neon/cold cathode, 2-wire uorescent

GL-EXP-DIMFDB-CN:

3-wire electronic uorescent dimming ballasts

GL-EXP-DIMFLV-CN:

LED, incandescent, uorescent, magnetic low-voltage,

electronic low-voltage, neon/cold cathode,

high-intensity discharge (HID), motor

GL-EXP-SW-CN:

LED, incandescent, uorescent, magnetic low-voltage,

electronic low-voltage, neon/cold cathode,

high-intensity discharge (HID), motor

Input Voltage 100 to 277 Vac, 50/60 Hz

Environmental

Temperature

Humidity

32° to 104 °F (0° to 40 °C)

10% to 90% RH (noncondensing)

Weight 3.4 lb (1.6 kg)

The dimensions for the GL-EXP-*-CN are shown in the following illustrations.

GL-EXP-*-CN Dimensions

5 13/16 in

(147 mm)

5/16 in

(9 mm)

8 5/16 in

(211 mm)

7 5/16 in

(186 mm)

8 5/8 in

(219 mm)

8 3/4 in

(223 mm)

1/2 in

(13 mm)

6 3/8 in

(163 mm)

(2x) Ø3/16 in

(5 mm)

(2x)

Ø3/18 in

(10 mm)

(2x) Ø1/4 in

(7 mm)

5 1/16 in

(129 mm)

3 13/16 in

(81 mm)

2 in

(52 mm)

Typ

1 13/16 in

(46 mm)

3 1/16 in

(78 mm)

(1-1/2 in

(39 mm)

Double ring knockout for 1/2 in and 3/4 in

conduit Ø.875 and Ø1.125 in after knockout

removal (typ).

Additional Resources

Visit the product page on the Crestron website (www.crestron.com)

for additional information and the latest rmware updates. Use a QR

reader application on your mobile device to scan the QR image.

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed

including the following:

READ AND FOLLOW ALL SAFETY INSTRUCTIONS.

• Do not use outdoors.

• Do not mount near gas or electric heaters.

• Equipment should be mounted in locations and at heights where it will not be

subjected to tampering by unauthorized personnel.

• The use of accessory equipment not recommended by the manufacturer may cause

an unsafe condition.

• Do not use this equipment for other than its intended use.

• All servicing should be performed by qualied service personnel.

• If any Emergency Circuits are fed or controlled from this panel, it must be located

electrically where fed from a UPS, generator, or other guaranteed source of power

during emergency and power outage situations.

SAVE THESE INSTRUCTIONS.

Installation

WARNING: To avoid re, shock, or death, turn off the power at the circuit breaker(s) or

fuse and test that power is off before wiring!

NOTE: Observe the following points:

• This product must be installed and used in accordance with the appropriate

electrical codes and regulations.

• This product must be installed by a licensed electrician.

• Use 75°C copper wire or better.

NOTE: Before using the GL-EXP-*-CN, ensure the device is using the latest rmware.

Check for the latest rmware for the GL-EXP-*-CN at www.crestron.com/rmware. Load

the rmware onto the device using Crestron Toolbox™ software.

Preparing and Connecting Cresnet, 0-10V, and Override Ports

Strip the ends of the wires approximately 7/16 in (11 mm). Use care to avoid nicking the

conductors. Tighten the connector to 5 in-lb (0.5 to 0.6 N-m). The wire gauge should be

14 to 26 AWG.

Installation

Mount the GL-EXP-*-CN to any vertical surface using four screws. The screws must be

appropriate for the mounting surface.

Installing the GL-EXP-*-CN Module

Mounting surface

(Qty. 4) Mounting

screws, #8 (not

included)

NOTE: To prevent potential heat damage to the drywall, do not mount the

GL-EXP-*-CN directly onto drywall. Mount the GL-EXP-*-CN to a piece of plywood that

is at least 1/2 in (13 mm) thick, and then mount the GL-EXP-*-CN and plywood to the

drywall.

NOTE: To ensure proper ventilation, the device must be installed vertically on a vertical

surface. Install the device with 6 in (153 mm) of clearance from the top and bottom of

the device.

Wiring Diagrams

WARNING: RISK OF SERIOUS PERSONAL INJURY. Turn off power at the circuit

breaker(s) prior to installation. Installing with power on can result in serious personal

injury and damage to the device.

Wire the GL-EXP-*-CN.

1. Use a #2 Phillips screwdriver to remove the cover screws and then remove the cover.

Remove Cover Screws

Cover

screws

2. Wire the device as shown below. An additional LINE, NEUT, and GND connection is

supplied for power to pass through. Keep the following in mind while wiring:

• Wires should be 10 to 24 AWG.

• Wires should be stripped to 5/16 in (8 mm).

• Tighten the terminal screws to 4.5 in-lbs (0.5 Nm).

Wire the GL-EXP-DIM-CN

Pass-through to

additional

module

From circuit

breaker

To dimmed

load

From

Override

switch

From

Cresnet

Bekijk gratis de handleiding van Crestron Green Light GL-EXP-SW-CN, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.