Continental SW72-N-GD handleiding
Handleiding
Je bekijkt pagina 3 van 32
3
OPERATIONS MANUAL
WORKTOP/UNDERCOUNTERS & SANDWICH UNITS
FIGURE 1: Data Tag
RECEIVING YOUR NEW MODEL
Congratulations on your purchase of Continental Refrigerator
superior foodservice equipment! When your shipment arrives,
thoroughly examine the packaging for any punctures, dents or
signs of rough handling. It is in your best interest to partially
remove or open the shipping container to examine the contents
for any missing accessories or concealed damage which may
have occurred during shipment. If the cabinet is damaged, it
must be noted on the carrier’s delivery slip or bill of lading
and a Freight Claim must be filed with the shipping company.
FREIGHT DAMAGE IS NOT COVERED UNDER WARRANTY.
GENERAL INFORMATION AND
IMPORTANT OPERATING FACTS
This manual has been compiled to aid in the installation, opera-
tion and maintenance of your new equipment. Please take the
time to read it and familiarize yourself with your equipment and
its operation, to enjoy optimum performance.
Continental Refrigerator offers a variety of accessories for your
model (see “Optional Accessories” section towards the back
of this manual or contact your dealer for more information).
SERIAL DATA TAG
A serialized data tag is permanently attached to the inside right-
hand wall of your unit. (see Figure 1). In addition to identifying
the specific product, this label provides important information
regarding electrical requirements and refrigeration charge, as
well as agency listings and factory contacts.
IMPORTANT NOTE: The model and serial number should
be noted on the front cover of this manual, in the spaces
provided. If parts or service are ever needed for your unit,
this information will be required to verify warranty status
and to properly identify any parts that may be needed.
All cabinets must be given sufficient time to reach normal
operating temperature before placing any food inside cabinet
or pans (if equipped). For refrigerators, approximately 1 hour
of operation is required to lower the cabinet and pan tempera-
ture to 40°F (4°C). During pull-down of open top models, pans
should be in place and top lid should be kept closed. Freezers
require approximately 2 hours of operation to lower the cabinet
temperature to 0°F (-18°C) (see “Operation” section for further
information).
Prior to factory shipping, all products are performance-run
tested for a minimum of 12 hours providing a highly sophis-
ticated temperature recording exclusive to each individual
cabinet. This recording is supplied within this manual packet. A
final evaluation, including analysis of cabinet performance, leak
check, vibration, noise level and visual examination is made by
a qualified quality control team to assure a superior product.
The carrier signs to this effect when they accept the product for
shipping. To insure the maximum in safety and sanitation, all
models are listed under applicable Underwriters Laboratories
and National Sanitation Foundation standards.
UNCRATING YOUR NEW MODEL
IMPORTANT: Your equipment should never be transport-
ed on legs/casters unless the cabinet bottom is properly
supported. Consult the factory for more information.
The shipping container should remain on your cabinet to avoid
dents or scratches while transporting to the actual set-up loca-
tion. All shelving, accessories and legs or casters are carefully
packaged and secured inside your cabinet to prevent damage.
After moving unit to its final location, remove all the staples
from around the bottom of the crate using a pry bar. Slide the
cardboard carton up and off the unit, being careful not to rub
against the cabinet. Remove any accessories or boxes on the
skid. Dispose of all packaging materials properly.
Four (4) bolts secure the cabinet to the wooden skid. The bolts
are located at each end on the underside of the skid. In order to
remove these bolts, tilt the cabinet backwards and place wooden
blocks at each end in order to hold it in its tilted position. Using
a ¾” socket or open end wrench, remove the bolts and carefully
slide the cabinet off of the skid. After skid removal, the cabinet
should never be moved without dollies or rollers to avoid dam-
age to the cabinet bottom or floor.
Bekijk gratis de handleiding van Continental SW72-N-GD, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Continental |
| Model | SW72-N-GD |
| Categorie | Koelkast |
| Taal | Nederlands |
| Grootte | 5643 MB |
