Continental CPA68 handleiding
Handleiding
Je bekijkt pagina 12 van 28
12
REFRIGERATED BASES & PIZZA PREP TABLES
OPERATIONS MANUAL
IMPORTANT NOTE: Turning a thermostat fully counter-
clockwise turns the refrigeration compressor “off.”
IMPORTANT NOTE: All refrigerators and Pizza Prep
Tables are designed with an automatic, “off-cycle”
defrost system which means that defrosting occurs auto-
matically when the compressor is not operating during an
off-cycle. Do not set the thermostat too cold where the
cabinet temperature will fall below 35°F (1.7°C) because
the evaporator will become blocked by ice since the com-
pressor off-cycle will be considerably shortened. This
will result in loss of product stored within the cabinet and
require service to defrost the evaporator and re-adjust
the thermostat.
DEFROST SYSTEM
(Pizza Prep and Freezer Base Models)
All Pizza Prep Tables feature a positive “off-cycle” defrost
system, with a timer that automatically initiates and terminates
compressor off-cycles, to ensure the evaporator remains frost-
free, even under heavy usage. All freezer defrost systems feature
a timer that initiates defrost cycles with a fail-safe cut-off time of
20 minutes, an automatic limit switch that provides temperature
termination of the defrost cycles, and electric heaters for posi-
tive thawing of the evaporator coil and drain pan, for optimum
performance.
The defrost timer on all pizza prep and freezer base models is
located in the machine compartment, behind the front grill on
CPA & CFA models (see Figure 11A) or behind the back panel
on CFB models (see Figure 5). If desired, the start time for a
defrost cycle can be adjusted by turning the knob on the defrost
timer clockwise until defrost cycle begins (compressor and all
fans will terminate). Defrost will begin at this same time every
day at 8-hour intervals. For example, if an 8:00 am defrost is
desired, at 8:00 am turn the timer knob to initiate defrost. A
defrost cycle will start every day at 8:00 am, 4:00 p.m., 12:00
am. If there is a loss of power to the cabinet, the defrost timer
will have to be reset to maintain the same defrost cycle times.
INTERIOR ACCESSORIES
SHELVING INSTALLATION
Your new unit is shipped with (1) shelf per section and (4) pilas-
ter clips for each shelf. Pilaster strips which support the shelving
are secured to the cabinet walls with special pilaster screws
which allow the strips to be readily removed for cleaning without
the use of tools. Shelf clips are easily installed by inserting them
into the pilasters at the desired shelf location (see Figure 12)
and the shelf simply sits on the clips.
FIGURE 11: CRB Components (Front View)
THERMOMETER
FAN MOTOR
(BEHIND PANEL)
TEMPERATURE CONTROL
GRILL
(REMOVED)
CONDENSER
(BEHIND GRILL)
EVAPORATOR
DRAIN PAN
CRB/CPT EVAPORATOR ASSEMBLY
FIGURE 12: Standard Shelf Pilaster
PILASTER
STRIP
PILASTER CLIP
INSTALLED
PILASTER CLIP
INSTALLING
SHELF
INSTALLING
FIGURE 11A: CPA/CRA Components (Front View)
EVAPORATOR
COVER
FAN MOTORS
(BEHIND PANEL)
THERMOMETER
TEMPERATURE
CONTROL
EVAPORATOR
DRAIN PAN
DEFROST TIMER
GRILL
(REMOVED)
CONDENSER
(BEHIND GRILL)
CPA EVAPORATOR ASSEMBLY
Bekijk gratis de handleiding van Continental CPA68, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Continental |
| Model | CPA68 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 5819 MB |
