Continental CPA60 handleiding
Handleiding
Je bekijkt pagina 16 van 28
16
REFRIGERATED BASES & PIZZA PREP TABLES
OPERATIONS MANUAL
INSTALLING FRONT BREATHER KIT
(CRB Models)
Disconnect cabinet power by unplugging cord from electri-
cal supply. Remove back panel to gain access to the machine
compartment (see Figure 14). Remove front grill and set aside
(standard grill is not used on front breathing models). Position
divider plate as shown and attach to cabinet with sheet metal
screws at front and self-drilling screws at back. Mount fan panel
to cabinet using sheet metal screws as shown. Attach fan panel
to divider plate with sheet metal screws. Plug fan power cord
into a standard 115 volt wall outlet or into the receptacle in the
cabinet control box labeled “vaporizer”, located at the back of the
machine compartment. Reattach back panel to cabinet. Install
special front breathing grill as shown. Do not use original stan-
dard grill! Reconnect power to the cabinet.
INSTALLING FRONT BREATHER KIT
(CPA and CRA Models)
Disconnect cabinet power by unplugging cord from electrical
supply. Remove back and/or side panel to gain access to the
machine compartment (see Figure 14A). Loosen (2) screws
on bottom of cabinet, towards front of machine compartment.
Position discharge duct under cabinet as shown and insert tab
into back edge of cutout on bottom of cabinet. Lift front of the
duct, so keyhole goes over screws in cabinet and duct is flat
against bottom of cabinet. Slide duct towards back of cabinet
and tighten screws. Position fan assembly as shown and place
into notch at rear of compressor compartment base. Secure with
(2) screws provided. Plug fan power cord into a standard 115
volt wall outlet or into the receptacle in the cabinet control box
labeled “vaporizer”, located at the front of the machine compart-
ment. Reconnect power to the cabinet.
FIGURE 14A: CPA & CRA Front Breather Kit
DISCHARGE DUCT
FAN
ASSEMBLY
REAR
ACCESS
PANEL
SIDE
PANEL
TAB
KEYHOLE
SCREW
CPA FRONT BREATHER KIT
DISCONNECT CABINET POWER BY UNPLUGGING CORD FROM ELECTRICAL SUPPLY. REMOVE BACK AND/OR
SIDE PANEL TO GAIN ACCESS TO THE MACHINE COMPARTMENT.
LOOSEN (2) SCREWS ON BOTTOM OF CABINET, TOWARDS FRONT OF MACHINGE COMPARTMENT.
POSITION DISCHARGE DUCT UNDER CABINET AS SHOWN AND INSERT TAB INTO BACK EDGE OF CUTOUT ON
BOTTOM OF CABINET. LIFT FRONT OF THE DUCT, SO KEYHOLE GO OVER SCREWS IN CABINET AND DUCT IS
FLAT AGAINST BOTTOM OF CABINET. SLIDE DUCT TOWARDS BACK OF CABINET AND TIGHTEN SCREWS.
POSITION FAN ASSEMBLY AS SHOWN AND PLACE INTO NOTCH AT REAR OF COMPRESSOR COMPARTMENT
BASE. SECURE WITH (2) SCREWS PROVIDED. PLUG FAN POWER CORD INTO A STANDARD 115 VOLT WALL
OUTLETIOR NTO THE RECEPTACLE IN THE CABINET CONTROL BOX LABELED "VAPORIZER", LOCATED AT THE
FRONT OF THE MACHINE COMPARTMENT. RECONNECT POWER TO THE CABINET.
FIGURE 14: CRB Front Breather Kit
CRB/CPT FRONT BREATHER KIT
FAN PANEL
ASSEMBLY
DIVIDER PLATE
FRONT
BREATHING
GRILL
BACK PANEL
RECEPTACLE
DISCONNECT CABINET POWER BY UNPLUGGING CORD FROM ELECTRICAL SUPPLY. REMOVE BACK PANEL
TO GAIN ACCESS TO THE MACHINE COMPARTMENT. REMOVE FRONT GRILL AND SET ASIDE. (STANDARD
GRILL IS NOT USED ON FRONT BREATHING MODELS.) POSITION DIVIDER PLATE AS SHOWN AND ATTACH
TO CABINET WITH SHEET METAL SCREWS AT FRONT AND SELF-DRILLING SCREWS AT BACK. MOUNT FAN
PANEL TO CABINET USING SHEETMETAL SCREWS AS SHOWN. ATTACH FAN PANEL TO DIVIDER PLATE WITH
SHEET METAL SCREWS. PLUG FAN POWER CORD INTO A STANDARD 115 VOLT WALL OUTLET OR INTO THE
RECEPTACLE IN THE CABINET CONTROL BOX LABELED "VAPORIZER", LOCATED AT THE BACK OF THE
MACHINE COMPARTMENT. REATTACH BACK PANEL TO CABINET. INSTALL SPECIAL FRONT BREATHING
GRILL AS SHOWN. (DO NOT USE ORIGINAL STANDARD GRILL!) RECONNECT POWER TO THE CABINET.
NOTE: ON CPT MODELS, THE PRESSEURE CONTROL MUST BE RELOCATED IN THE MACHINE
COMPARTMENT TO THE UNDERSIDE OF THE CABINET TOP, ABOVE THE FAN PANEL ASSEMBLY.
END PANEL
NOT SHOWN
FOR CLARITY
ANY RESTRICTIONS TO THE AIR FLOW THROUGH THE
FRONT GRILL OR UNDER THE CABINET CAN DAMAGE
THE REFRIGERATION SYSTEM AND WILL VOID ALL
WARRANTIES.
INSTALLING DRAWER CAGE
NOTE: These instructions assume that doors already on
the unit have been removed.
Using a flat head screwdriver, pry both vertical breaker covers
away from the primary breakers beneath them, being careful not
to damage the heater wires (see Figure 15). Carefully slide the
cage into the opening. The cage must be lifted above the breaker
corners in order to fit into the opening. The fit is tight, so the
straighter it’s pushed in, the easier it will be. With the cage in
as far as it will go, the notches at the bottom front should sur-
round the breaker corners, and the cage should be sitting flat on
the interior floor of the unit. The front face of the cross mullion
should be flush with the front face of the unit. You may need
to tap the inside face of the cross mullion in order to achieve
this. This allows the drawer gasket to seal smoothly around the
drawer opening.
With the cage in place, sitting flat on the floor of the unit and
flush with the front, drill 1/8” pilot holes through each of the
four (4) front mounting holes, through the primary breakers, and
through the metal beneath them. Drive a sheet metal screw into
each of the front mounting holes, securing the front of the cage
to the inside front of the opening, as tightly as possible without
stripping the screw threads or head. Drive a sheet metal screw
Bekijk gratis de handleiding van Continental CPA60, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Continental |
| Model | CPA60 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 5819 MB |
