Cigweld BlueVenom 4R-Rover handleiding
Handleiding
Je bekijkt pagina 61 van 72
5.21 MIG (GMAW) WELDING PROBLEMS
PROBLEM CAUSE REMEDY
1 Mains Supply Voltage is connected
to the Power Source, the On/Off
switch on the rear panel of the
Power Source is in the On position,
the Power Source Front Panel
Digital Display is illuminated and
the Remote Feeder is correctly
connected however there are only
Dashes displayed on the Remote
Feeder Front Digital Displays and it
will not MIG weld.
Power source is not in the correct
mode of operation for the Remote
Feeder.
A Set the power source to Remote Feeder
mode. Refer to Section 4.02 D.
2 Mains Supply Voltage is connected
to the Power Source, the On/
Off switch on the rear panel of
the Power Source is in the On
position, the Power Source Front
Panel Digital Display is illuminated
and the Remote Feeder Front
Digital Display is illuminated and
functional but will not MIG weld.
A Power Source MIG Gun Polarity Lead is
not connected
A Connect the Power Source MIG Gun Polarity
Lead to the positive or negative output
terminal. Refer to Section 5.17. or Setups for
MIG Welding Sections 5.10 – 5.13.
B Work Lead is not connected to the work
piece
B Ensure that the Work Lead is connected to
the work piece and has a good connection
to the work piece. Refer to Setups for MIG
Welding Section 5.10 - 5.13.
C MIG Gun is not correctly connected to the
Euro Style MIG Gun Adaptor.
C Ensure that the MIG Gun is correctly
connected to the Euro Style MIG Gun
Adaptor. Refer to Section 4.01.3 & 5.02.
3 Mains Supply Voltage is connected
to the Power Source, the On/Off
switch on the rear panel of the
Power Source is in the On position,
the Power Source Front Panel
Digital Display is illuminated but
the Remote Feeder Front Digital
Display is Not illuminated and will
not MIG weld.
10 Pin Interconnection Lead Control Plugs
are not connected correctly.
Check the 10 Pin Control Plug connections
at both the Power Source Socket and the
Remote Feeder Sockets are connected
correctly and rmly. Refer to Setups for MIG
Welding Section 5.10 - 5.13.
4 When welding at maximum output
(WFS and Volts) the machine stops
welding.
A When output amperage exceeds the
rated maximum output of the machine
the welding machine will sense this and
initiates a safety circuit which stops the
output current and displays an Output
Over Current Error Code 08. Refer to
Section 6.06 Error Codes for further
detail.
A Reduce output amperage (WFS and Volts).
B Contact Tip of the MIG gun is too close
to the work piece.
B Increase distance between the Contact Tip
of the MIG gun and the work piece.
C The Pre-set voltage is too high. C Decrease the Pre-set voltage.
D The MIG Welding Wire in use is not
consistent with the selected MIG wire
diameter, e.g. 0.8mm wire is selected
but 0.9mm wire is used.
D Ensure that the correct MIG Welding
Wire Diameter is selected for MIG Wire
being used. Refer to Section 5.10
OPERATING MANUAL BLUEVENOM 4R-ROVER
CIGWELD.COM.AU | 61
Bekijk gratis de handleiding van Cigweld BlueVenom 4R-Rover, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Cigweld |
| Model | BlueVenom 4R-Rover |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 11536 MB |
