Cicada Audio DSP88V2 handleiding
Handleiding
Je bekijkt pagina 5 van 17
4
2021 Cicada Audio All rights reserved.
ABOUT CICADA AUDIO
Introduction
SPECIFICATIONS
PWR/PRT LED - This light indicate when the amplifier is powered up normally and when there is a protection fault.
The Protect LED is illuminated when there is a problem with your amplifier. Please contact your authorize
Cicada Audio dealer or call Cicada Audio’s technical support.
GAIN (Input Gain Adjustment) - This control matches the preamp INPUT stage of the Cicada Audio amplifier to your
source unit. This is NOT a volume control. The range is between approximently 200mV and 10V. It can ALSO handle
speaker inputs of less than 25 watts RMS (typical OEM headunits are LESS than 25 W RMS,...but NOT all)
TURN-ON OPTIONS - The Cicada Audio DSP88 can be switched on and off using one of two methods, determined
by the position of the amplifier’s “Turn-On Mode” switch. Please read the “Set-Up ” portion of this guide and
determine which is best suited for your specific system. NOTE: DC and VOX turn-on settings ONLY work with
speaker level input.
USB C - Input for connecting a PC to use ONLY for updating Firmware. ONLY!!!
BlueTooth Dongle - (Plug in) This makes it so the DSP125.4D can be programmed by phone or tablet for all DSP
tuning.
Front RCA Input Terminal (CH1 /2 ) - The RCA jacks allow for a normal Left and Right channel signal input. Simply
connect to the source unit using RCA type audio cables, keeping them away from power wiring wherever possible to
reduce risk of noise. NOTE: This input can be used for “speaker level” input by using the optional Speaker Hanress
HDFIM/HDRIM (with load resistors), or by simply cutting and attaching OEM head unit speaker outputs to these
wires. Or cut up an old RCA cable and connect your HD radio speaker wires that way (Better solution)
Rear RCA Input Terminal (CH3 /4 ) - The RCA jacks allow for a normal Left and Right channel signal input. Simply
connect to the source unit using RCA type audio cables, keeping them away from power wiring wherever possible to
reduce risk of noise. NOTE: This input can be used for “speaker level” input by using the optional Speaker Hanress
HDFIM/HDRIM (with load resistors), or by simply cutting and attaching OEM head unit speaker outputs to these
wires.
RCA Output Terminal - The RCA jacks allow for a pre amp level CH5/6 output to create a 6 channel system. Which
could be subwoofers or midbass or full range drivers
Front Speaker Output Terminal - Connect your Front speakers to these wires. Stereo connections are connected as
labeled. Bridged connections use the LEFT + and RIGHT - as the two connections. The 2 and 4 channel amplifiers
will perform into 2 Ohm stereo loads or 4 Ohm bridged loads. DO NOT run 2 Ohm bridged loads on AND CIcada
Audio amplifers. They will work, but will over heat very quickly.
Rear Speaker Output Terminal - Connect your Rear speakers to these wires. Stereo connections are connected as
labeled. Bridged connections use the LEFT + and RIGHT - as the two connections. The 2 and 4 channel amplifiers
will perform into 2 Ohm stereo loads or 4 Ohm bridged loads. DO NOT run 2 Ohm bridged loads on AND CIcada
Audio amplifers. They will work, but will over heat very quickly.
Power Input Connections - These connections are for input power(12V), chassis ground (GRD), and remote(REM)
turn-on. Use a minimum of 8 gauge wiring for power and ground connections. The terminals will handle up to 8
gauge wiring with no problem what so ever. Be sure any wiring that passes through metal has a grommet!
DIMENSIONAL DRAWINGS
FOR FITMENT
1.26” / 32mm
4.04” / 102.5mm
5.12” / 130mm
Bekijk gratis de handleiding van Cicada Audio DSP88V2, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Cicada Audio |
| Model | DSP88V2 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 9694 MB |