Champion DH3000 handleiding
Handleiding
Je bekijkt pagina 6 van 79
LIMITED WARRANTYLIMITED WARRANTY
LIMITED WARRANTY
Champion Industries, Bi-Line Systems (herein referred to as (“The
Companies”), 3765 Champion Blvd., Winston-Salem, North Carolina,
27105) warrants machines and parts, as set out below:
WARRANTY OF MACHINES:
The Companies warrant all new machines of its manufacture bearing
the name Champion or Bi-Line and installed within the United States to
be free from defects in material and workmanship for a period of one
(1) year from the date of installation or fteen (15) months from the date
of shipment by The Companies, whichever occurs rst. This Limited
Warranty does not cover products shipped outside of the United States.
The warranty registration card must be returned to The Companies
within ten (10) days after installation or registered online at www.
championindustries.com/warranty-registration for the United States; or
by fax using the form provided at the front of this manual. If the warranty
card, fax, or email are not sent to The Companies within fteen (15) days,
then the warranty will expire after fteen (15) months from the date of
shipment. The Companies will not assume any responsibility for additional
installation costs in any area with jurisdictional problems with local trades
or unions. The Companies reserves the right to repair or replace a
defective part or the entire machine, if a defect in workmanship or material
is identied within the warranty period. Alternatively, The Companies may
elect to accept the return of the machine for a full credit. In the event
If The Companies elect to repair then the labor and work performed in
connection with the warranty shall be done by The Companies’ authorized
service agent during regular working hours and at regular labor rates.
Overtime charges are the responsibility of the equipment purchaser.
Warranty travel is be covered up to fty (50) miles from the authorized
service technician’s servicing oce. If travel exceeds fty (50) miles, the
end user will be responsible for any additional travel expense. Service
calls initiated under warranty and found not to contain any defects
in materials or workmanship, will not be covered by The Companies
warranty. Defective parts become the property of The Companies. Use
of non-OEM replacement parts, not authorized by The Companies, will
relieve The Companies of all further liability in connection with its warranty.
In no event, will The Companies’ warranty obligation exceed the charge
for the machine. Machines that come with a factory-paid start-up will be
limited to one (1) authorized service call for start-up. Installation problems
or delays, of any kind, will not be covered by The Companies’ warranty
and will be the sole responsibility of the equipment purchaser.
THE WARRANTY DOES NOT COVER:
a. Chemical tubing, chemical squeeze tubes, O-rings, or curtains.
b. Vacuum breakers.
c. Adjustments to structural or mechanical components covered by
recommended maintenance procedures.
d. Replacement of fuses, resetting of overload breakers, or high-limit
thermostats.
e. Adjustments of thermostats or other temperature controlling devices.
f. Adjustments of clutches.
g. Adjustments of water pressure(s).
h. Adjustments of factory chemical pumps and settings.
i. Opening or closing of utility supply valves or switching of electrical
supply current.
j. Cleaning of valves, strainers, screens, nozzles, or spray pipes.
k. Regular maintenance and cleaning as outlined in the operator’s guide.
l. Damages resulting from water conditions, accidents, alterations,
improper use, abuse, tampering, improper installation, under or over
voltage conditions, power surges, inadequate wiring, outdoor use, or
failure to follow maintenance and operation procedures.
m. Pulper cutter blocks, pulse vanes, and auger brush due to wear and tear.
n. Damages due to improper storage.
o. Special installations or applications, including remote locations, are
limited in coverage by this warranty.
p. Any installation that requires additional work and/or travel to gain
access to a machine for service is the sole responsibility of the
equipment purchaser.
THE FOLLOWING DEFECTS ARE NOT COVERED BY
THE WARRANTY:
1. Damage to the exterior or interior nish.
2. Damage caused by improper connection to utility service other than
that designated on the rating plate.
3. Inadequate or excessive water pressure.
4. Corrosion due to foreign materials, improper water supplies,
improper chemicals, or chemicals dispensed in excess of
recommended concentrations.
5. Failure of components due to the connection of third-party chemical
dispensing equipment installed by others.
6. Leaks and damage due to the use of non-specied water quality.
7. Leaks and damage caused by the installer, including machine
table connections.
8. Leaks or damage caused by chemical dispensing equipment
connections installed by others.
9. Failure to comply with all local building codes.
10. Damage caused by labor dispute.
WARRANTY OF PARTS:
The Companies warrant all new machine parts produced or authorized by
The Companies to be free from defects in material and workmanship for
a period of ninety (90) days from the date of invoice. If any parts defect
in material and workmanship is found to exist within the warranty period,
then The Companies will refund the cost of the defective part.
DISCLAIMER OF WARRANTIES AND LIMITATIONS
OF LIABILITY.
THE COMPANIES’ WARRANTY IS ONLY TO THE EXTENT REFLECTED
ABOVE. THE COMPANIES MAKE NO OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO ANY
WARRANTY OF MERCHANTABILITY OR FITNESS OF PURPOSE.
THE COMPANIES SHALL NOT BE LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES. THE REMEDIES SET OUT ABOVE ARE
THE EXCLUSIVE REMEDIES FOR ANY DEFECTS FOUND TO EXIST IN
MACHINES AND PARTS OF THE COMPANIES. ALL OTHER REMEDIES
ARE EXCLUDED, INCLUDING ANY LIABILITY FOR INCIDENTALS OR
CONSEQUENTIAL DAMAGES.
Champion Industries or Bi-Line Systems does not authorize any other
person, including persons who deal in Champion Industries or Bi-Line
Systems machines, to change this warranty or create any other obligation
in connection with Champion Industries or Bi-Line Systems machines.
Champion Industries/Bi-Line Systems • 3765 Champion Blvd., Winston-Salem, 27105, North Carolina, USA
Tel: (336) 661-1556, Fax: (336) 661-1979, email: sales@championindustries.com6
Bekijk gratis de handleiding van Champion DH3000, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Champion |
| Model | DH3000 |
| Categorie | Vaatwasser |
| Taal | Nederlands |
| Grootte | 9847 MB |
