Cecotec Bolero DressCode 9500 Inverter A handleiding

Wasmachine

Cecotec

128 pagina's

PDF beschikbaar

Handleiding

BOLERO DRESSCODE 9500 INVERTER A / BOLERO DRESSCODE 9500 INVERTER STEEL A

6564

ENGLISH ENGLISH

Connecting the drain hose

- The drain hose should be placed at a height of 65-100 cm above the ground, otherwise it

may cause poor drainage. Fig. 12

- You can use the drain-hose bracket supplied to connect the drain hose to the wall, drain

pipe, or sink. Fig. 13

- Make sure that all hose connections are tight.

Please note

Do not immerse the end of the drain hose in water for the washing machine to work properly.

Electric connection

- Since the maximum current ow is 10 A when the interior temperature of the washing

machine increases, make sure that the power supply system (current, supply voltage, and

cord) in your home can meet the normal load requirements of electrical appliances.

- Connect the appliance to a properly installed and earthed outlet.

- Make sure that the household supply voltage matches the rated voltage of the washing

machine.

- Make sure the power plug matches the socket.

- Do not use multipurpose plugs, sockets, or extension cords.

- Do not connect or disconnect the plug with wet hands.

- When disconnecting the plug, hold it rmly and pull it out. Do not pull the power cord out

abruptly.

Warning

1. The washing machine must be properly earthed. If a short circuit occurs, earthing can

reduce the risk of electric shock.

2. The washing machine must be operated on a circuit separate from other electrical

appliances. Otherwise, the surge protector may trip, or the fuse may blow.

Washing machine operation

Please note

Make sure that the washing machine is properly installed before use.

Before rst use, you should perform a complete washing cycle without laundry.

First use

1. Connect the power cord and inlet hose as described in the previous section.

2. Add some detergent (about 10 g) to the detergent drawer and close it.

3. Press the Power button.

4. Turn the selection knob to the Cotton position.

5. Press the Start/Pause button.

This will remove any water left in the washing machine from the manufacturer's test.

Please note

The levelling feet do not come fully xed for easier installation, so be sure to x all four before

levelling the washing machine.

1. When positioning the washing machine, you should check if the levelling feet are fully

xed; if not, x them. The lock nuts must be rmly locked to the bottom of the appliance

and the levelling feet securely locked into the lock nuts. Fig. 7

2. Once the washing machine is installed, press on the opposite corners of the top with both

hands in succession and shake the washing machine vertically downwards to check if the

levelling feet are rmly xed and that the washing machine does not wobble. Fig. 8

3. If the washing machine wobbles, loosen the lock nut in the direction shown in Figure 9 with

the spanner provided until the machine is level and no longer wobbles. Fig. 9

4. Finally, use the spanner to x the lock nut to the bottom of the washing machine (you can

also x the levelling feet lightly by hand to prevent them from moving). Make sure the

levelling feet do not move. Fig. 10

Warning

1. The washing machine must be perfectly level and stabilised when all four feet are rmly

on the oor.

2. Incorrect levelling adjustment may cause loud noises, vibrations of the washing machine,

shifting of the washing machine, and other abnormal occurrences.

3. The air vent is located at the bottom of the washing machine (to avoid obstructions). Install

the washing machine on a solid, smooth, non-slip oor. Do not place the washing machine

on a soft blanket or wooden oor or on top of furniture, as this may cause unnecessary

injury.

4. OPERATION

Installing the washing machine

Connecting the inlet hose Fig. 11

1. Connect the inlet hose to the tap and x it by turning it counterclockwise.

2. Connect the other end of the inlet hose to the inlet valve on the back of the washing

machine and secure it rmly clockwise.

Please note

- If the hose leaks after connection, repeat the process.

- Do not bend the hose.

- Check the inlet hose connection before every use.

Bekijk gratis de handleiding van Cecotec Bolero DressCode 9500 Inverter A, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.