Handleiding
Je bekijkt pagina 2 van 5
5. Pivot the motor platform to tension the V-belt and lock in place using the 2 bolts on both sides of the blower. (Ideal belt tension
is the lowest tension at which the belt will not slip during start up.) As shown in illustration to right, a proper deflection of 1/64 of
the belt span is desired for belt tension.
5"
6" 7" 8" 9" 10" 12"
824-1125 RPM
680-929 RPM 580-792 RPM 505-690 RPM 447-611 RPM 401-548 RPM 533-455 RPM
4L37 4L39 4L41 4L42 4L44 4L45 --
4L39 4L41 4L42 4L44 4L46 4L47 --
4L42 4L44 4L46 4L47 4L49 4.51 --
-- -- -- -- 4L55 4L57 4L60
-- -- -- -- 4L59 4L60 4L64
Motor Pulley
Cast Iron
Blower Pulley
Cast Iron
RPM
Range
SIS-9
SIG-9
SIS-10
SIG-10
SIS-12
SIG-12
SIS-15
SIG-15
SIS-18
SIG-18
SIS-20
BEL
T LENGTH
BASED ON
MOTOR FRAME
HB47T 1630 - 1232
B37 B39 B43
-- -- --
HB57T 1329 - 1005 B39 B41B44
-- -- --
HB67T 1121 - 848B40B43B46
-- -- --
HB77T 969 - 733 B42B44 B48 B52 B56
--
HB87T 854 - 645B43B46B49B54 B57
--
HB97T 763 - 577 B46B48 B51 B56 B59
--
HB107T 690 - 521 B47 B50 B53 B58 B61
--
HB117T 629 - 476 B49 B51 B55 B59 B63
--
HB127T 578 - 437
B51 B53 B55 B61 B64
--
HB137T 535 - 404 B53 B55 B58 B63 B66
--
HB157T466 - 352 B57 B59 B62
--
B70
--
HB187T 390 - 295 B64 B65 B68
-- -- --
HB77T
756 - 568 -- -- --
B51 B54
--
HB87T
667 - 500 -- -- --
B53 B56
--
HB97T
596 - 447 -- -- --
B55 B58
--
HB107T
538 - 404-- -- --
B56 B60
--
HB117T
491 - 368 -- -- --
B58 B61
--
HB127T
452 - 339 -- -- --
B60 B63
--
HB137T
418 - 314-- -- --
B62 B65
--
HB157T
364 - 372 --
-- -- -- B69 --
HB87T 854 - 645 -- -- -- -- --
B79
HB97T
763 - 577 -- -- -- -- --
B81
HB107T
690 - 521 -- -- -- -- --
B83
HB117T
629 - 476 -- -- -- -- --
B84
HB127T
578 - 437 -- -- -- -- --
B86
HB137T
535 - 404-- -- -- -- --
B88
HB157T
466 - 352 -- -- -- -- --
B91
HB187T
390 - 295 -- -- -- -- --
B97
HB117T
828 - 686 -- -- -- -- -- B86
HB127T
756 - 618 -- -- -- -- -- B88
HB137T
697 - 575 -- -- -- -- -- B90
HB157T
616 - 509 --
-- -- -- -- B93
12.4 X 2B
830 - 700 -- -- -- -- -- B90
13.6 X 2B
759 - 631 -- -- -- -- -- B92
FOR FRACTIONAL HP APPLICATIONS "4L" BELTS MAY BE SUBSTITUTED BY ADDING 2" TO THE SPECIFIED "B" BELTS. Eg. B50 BELT = 4L52
BLOWER MODEL
BELT LENGTH
BASED ON
MOTOR FRAME
3 1/4 CAST IRON BLOWER PULLEY - DIAMETER & RPM RANGE
48 FRAME
56 FRAME
IVL44
O.D. 4.15"
SIS-9 / SIG-9
SIS-10 / SIG-10
SIS-12 / SIG-12
SIS-15 / SIG-15
SIS-18 / SIG-18
DOUBLE GROOVE
D8600
O.D. 6"
8550
O.D. 5.35"
213, 215T
FRAME
182, 184T FRAME
(DEDUCT 2" FOR
56, 143, & 145T)
48 FRAME
(ADD 1" FOR 56
FRAME)
MODELS SIS-15,
SIG-15 & SIS-18,
SIG-18
143, 145T FRAME
8325
O.D. 3.25"
143T & 145T
FRAME
8400
O.D. 4.15"
182, 184T FRAME
(DEDUCT 2" FOR
56, 143, & 145T)
SIS/SIG SERIES
SIDE INTAKE SUPPLY UNIT / SIDE INTAKE GALVANIZED SUPPLY UNIT
SIS_SIG-M-07_20_16 Page 2 of 5
MOTOR, PULLEYS & BELTS (See Table below)
t
t
w
A
WARNING
EXCESSIVE BELT TENSION IS THE MOST FREQUENT CAUSE OF BEARING WEAR AND RESULTING NOISE.
PROPER BELT TENSION IS CRITICAL FOR QUIET EFFICIENT OPERATION.
Ideal belt tension is the lowest value under which belt slip will not occur at peak load conditions.
BELT ALIGNMENT
FIGURE 1
XX
Bekijk gratis de handleiding van Canarm SIS1530300M, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Canarm |
| Model | SIS1530300M |
| Categorie | Afzuigkap |
| Taal | Nederlands |
| Grootte | 1098 MB |
