Broan QTXE110S handleiding

Handleiding

123456789101112/ 12

Afdrukken

Je bekijkt pagina 2 van 12

Page 2

MODELS QTXE110S • QTXE110S2

TYPICAL INSTALLATIONS

Housing mounted to

I-joists.

Housing mounted anywhere

between trusses using hanger

bars.

PLAN THE INSTALLATION

1. Choose the

installation

location.

The location of

your humidity

sensing fan is

very important.

Use the follow-

ing guidelines

for best opera-

tion:

Housing mounted anywhere be-

tween I-joists using hanger bars.

Housing mounted to joists.

Housing mounted anywhere be-

tween joists using hanger bars.

Housing mounted anywhere be-

tween trusses using hanger bars.

INSTALL HOUSING &

DUCT

1a. Mount

housing

to joist

or I-joist.

Use a pliers to

bend housing

TABS out to

90

0

. Hold hous-

ing in place so

that the hous-

ing tabs con-

tact the bottom

of the joist.

The housing

mounts with

four (4) screws

or nails. Screw

or nail housing

to joist through

lowest holes in

each mount-

ing flange,

then through

highest holes.

SPACER

(use for mounting to I-Joist)

TABS

I-JOIST

NOTE: Mounting to I-JOIST (shown) requires use of

SPACERS (included) between the highest hole of each

mounting flange and the I-joist.

OR

• Locateunitabove(GFCIprotectedcircuitrequired)or

within 5 feet of shower head.

• Locateunitawayfromheatingorcoolingsources

which can affect humidity levels.

• Donotlocatenearwindow.Unitmayrespondtothe

outdoor humidity level.

• Unitmustbeinstalledinceilingtoproperlysense

moisture.

• Locateunitonlyonflatceilingsupto12feethighfor

proper sensing.

• Theductingfromthisfantotheoutsideofthebuilding

has a strong effect on the air flow, noise and energy

use of the fan. Use the shortest, straightest duct rout-

ing possible for best performance, and avoid installing

the fan with smaller ducts than recommended. Insula-

tion around the ducts can reduce energy loss and

inhibit mold growth. Fans installed with existing ducts

may not achieve their rated airflow.

2. Plan the wiring.

• Plantosupplytheunitwithproperlinevoltageand

appropriate power cable. Power cable should be

routed to the switch box first and then to the unit

(See “CONNECT WIRING” on page 3).

• Donotoperatethisunitwithaspeedcontrol. 

Damage to the sensor unit will result.

*Purchase

separately.

INSULATION*

(Place around and

over Fan Housing.)

ROOF CAP*

(with built-in

damper)

FAN

HOUSING

POWER

CABLE*

6-IN. ROUND

DUCT*

6-IN.

ROUND

ELBOWS*

Seal gaps

around

Housing.

Seal duct

joints with

tape.

OR

Keep duct

runs short.

WALL CAP*

(with built-in

damper)

123456789101112/ 12

Bekijk gratis de handleiding van Broan QTXE110S, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.

Productinformatie

Gerelateerde producten van Broan (Ventilator)

Handleiding bekijken

Broan Ultra Pro RB110

Ventilator - handleiding

Handleiding bekijken

Broan CST80SLW

Ventilator - handleiding

Handleiding bekijken

Broan ZB80L1

Ventilator - handleiding

Handleiding bekijken

Broan Roomside AER110LTKC

Ventilator - handleiding

Handleiding bekijken

Broan XB80

Ventilator - handleiding

Handleiding bekijken

Broan L150EL

Ventilator - handleiding

Handleiding bekijken

Broan L300EL

Ventilator - handleiding

Handleiding bekijken

Broan Roomside AR80MB

Ventilator - handleiding

Andere merken in Ventilator