Handleiding
Je bekijkt pagina 9 van 36
9
Note:Worktops that are between 12 mm and 20
mm thick must be used with a spacer, which is avail-
able from technical customer service.
Preparing the built-in unit for flush installation (b)
¡ Only use worktops that are at least 30 mm thick.
Installation on a drawer or cupboard
WARNING‒Risk of burns!
The accessible parts may become hot during opera-
tion.
If there is no built-in oven underneath the hob and
the underside of the hob is accessible, follow these
instructions:
For gas hobs with wok burner, insert a non-flamable
intermediate floor (e.g. metal or ply-Wood) at a dis-
tance of 10 mm from the hob .
→Fig.
4
For gas hobs without a wok burner, it is advisable to
fit an intermediate floor underneath the hob .
→Fig.
5
In both cases, the distance from the intermediate
floor to the mains connection for the appliance must
be at least 10 mm.
The thickness of the separator must allow for re-
specting the distances in the figure.
Installation above an oven
→Fig.
6
Positioning the appliance
1. Position the hob with the upper side facing down
on a flat, stable surface.
2. Apply the adhesive seal supplied to the lower
edge of the hob. The adhesive seal prevents the
penetration of liquids.
→Fig.
7
3. Screw the brackets supplied into the specified po-
sition so that they can turn freely.
→Fig.
8
4. Turn the hob around and insert it into the recess.
Insert the hob in the front of the recess.
→Fig.
9
5. Turn the brackets and tighten them fully.
→Fig.
10
The position of the brackets depends on the work-
top thickness.
Note:Do not use silicone to bond the appliance to
the worktop.
Installing the appliance flush
Note:Only use worktops at least 30 mm thick.
1. Install the appliance so that there is an even gap
all around it. →"Positioning the appliance",
Page9
‒ The hob should be slightly below the work sur-
face. On tiled worktops, the contact surfaces
can be raised, if necessary, with temperature-
and water-resistant rails.
→Fig.
11
2. Check that the appliance works correctly and is in
the correct position.
3. Fill the gap between the work surface and the hob
using a suitable commercially available silicone
adhesive.
→Fig.
12
Smooth the silicone adhesive with a spatula or a
finger wetted with soap before a solid layer forms.
Note:Leave the silicone adhesive to dry before you
use the appliance.
Tip:If you use an unsuitable silicone adhesive on
natural stone work surfaces, it may cause discolour-
ation that can no longer be removed. A suitable ad-
hesive is available from our technical customer ser-
vice.
Removing the appliance
1. Disconnect the appliance from the electricity and
gas connections.
2. Unscrew the brackets and proceed in reverse or-
der.
Connecting the gas
Observe the country-specific guidelines.
CAUTION‒Risk of explosion!
A gas leakage may cause an explosion.
▶
If any connection is handled, check the seal.
¡ Arrange the gas connection so that the shut-off
valve is accessible.
¡ Ensure that the information on the rating plate re-
garding the gas type and gas pressure complies
with the local connection conditions.
¡ Connect the appliance to a fixed gas pipe or a flex-
ible metal pipe.
¡ The flexible metal pipe must not come into contact
with the moving parts of the unit in which the appli-
ance is installed (e.g. a drawer) and must not be
routed through any spaces which might become ob-
structed.
¡ Gas connection elbow on the appliance: R 1/2.
¡ Do not move or twist the gas connection elbow.
Connection to gas cylinder or liquid gas tank
▶
If the flame is large or unstable, check that the
regulator of the gas cylinder or liquid gas tank is
working properly.
Note:You can install an overpressure safety device
that limits or cuts off the gas supply if the regulator
of the gas cylinder or liquid gas tank fails.
Spare parts for gas connection
If the country's regulations allow, you can obtain the
gas connection parts from the technical customer
service.
→Fig.
13
Gas connection R 1/2
→Fig.
14
Gas connection G 1/2
1. Replace the gas connection elbow on the appli-
ance with the gas connection elbow G 1/2 sup-
plied in the accessory bag.
→Fig.
15
2. Insert the seal between the gas connection of the
appliance and the gas supply.
Electrical connection
¡ This appliance is type Y: The connection cable must
only be replaced by technical customer service and
not by the user. The cable type and the minimum
cross section must be respected.
¡ The hobs are supplied with a power cord with or
without a plug.
¡ The power cable must only be replaced with a cable
from the original manufacturer. This is available
from after-sales service.
¡ Do not use extension cables or multiple socket
strips.
¡ Only connect appliances that are fitted with a plug to
a correctly installed socket with protective earth con-
ductor.
Bekijk gratis de handleiding van Bosch PPQ7A6I15, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Bosch |
| Model | PPQ7A6I15 |
| Categorie | Fornuis |
| Taal | Nederlands |
| Grootte | 5616 MB |
