Handleiding
Je bekijkt pagina 10 van 32
10
WARNING‒Risk of explosion!
Escaping gas may cause an explosion.
▶
All Installation, connection, regulating and conver-
sion work to a different gas type must be carried
out by an authorised professional while taking into
account the respective applicable regulations and
legal requirements as well as the regulations re-
garding the local electricity and gas suppliers.
Special attention must be paid to the provisions
and guidelines that are applicable for the ventila-
tion. For conversion work to a different gas type,
we recommend that you call the after-sales ser-
vice.
WARNING‒Danger: Magnetism!
Caution: Magnetic field
Attention for persons with pacemakers
Permanent magnets are integrated in the control ele-
ment bases and the control elements. Magnets may
affect electronic implants, e.g. heart pacemakers or
insulin pumps.
▶
Persons with electronic implants must stand at
least 10cm away from the magnetic control ele-
ment bases and control elements.
▶
Never carry the control element base and the con-
trol elements on your body.
¡ Ensure that the kitchen is sufficiently ventilated, in
particular when operating the gas cooking appli-
ance.
¡ Do not connect the appliance to an exhaust gas
system for combustion products.
¡ Never install the appliance in boats or in vehicles.
¡ The warranty applies only when using the appli-
ance as intended.
¡ Before installing the appliance, check that the
local conditions of the supplier are compatible
with the appliance settings specified on the rating
plate (type of gas and pressure, power, voltage).
¡ Secure the power cord to the cabinet to prevent it
from touching hot parts of the oven or hob.
¡ Before any work is carried out on the appliance,
switch off the power supply and the gas supply.
¡ Connect the appliance to the power supply using
the earth.
¡ Do not make any changes to the inside of the ap-
pliance. If required, contact our technical cus-
tomer service.
Before installing
¡ This appliance is a class 3 appliance in accord-
ance with the EN 30-1-1 standard for gas appli-
ances: Built-in appliance.
¡ The unit in which the appliance is installed must
be stable and secured appropriately.
¡ The units in the vicinity of the appliance, the lamin-
ated panels and the adhesive with which they are
secured must be made of non-flammable, heat-
resistant materials.
¡ Do not install this appliance above refrigerators,
washing machines, dishwashers or similar.
¡ The appliance must only be installed on an oven
with forced ventilation. Check the dimensions of
the oven in the installation instructions for the
oven.
¡ If you install an oven underneath the hob, the work
surface thickness may differ from the dimensions
given in these instructions. Take note of the in-
formation in the oven installation instructions.
¡ The distance between the top edge of the cooker
and the bottom edge of the extractor hood filter
must meet the requirements of the extractor hood
filter manufacturer. If no reference is made to the
guidance for the extractor hood in the hob's in-
stallation instructions, this distance must be at
least 650mm.
→Fig.
1
Preparing the units
¡ Make a cut-out in the worktop with the required di-
mensions.
→Fig.
2
¡ Any panel that is attached closer to the built-in
niche than the specified clearance must be made
of non-combustible material. Always maintain a
distance of at least 5mm between the panel and
the appliance. Maximum clearances for the panel:
30 mm thickness x 70 mm height.
¡ Seal the cut surfaces of wooden work surfaces
with a special glue seal to protect them from mois-
ture.
WARNING‒Risk of burns!
The accessible parts may become hot during opera-
tion.
If there is no built-in oven underneath the hob and
the underside of the hob is accessible, follow these
instructions:
For gas hobs with wok burner, insert a non-flamable
intermediate floor (e.g. metal or ply-Wood) at a dis-
tance of 10 mm from the hob .
→Fig.
3
For gas hobs without a wok burner, it is advisable to
fit an intermediate floor underneath the hob .
→Fig.
4
In both cases, the distance from the intermediate
floor to the mains connection for the appliance must
be at least 10 mm.
The thickness of the separator must allow for re-
specting the distances in the figure.
Installation above an oven
→Fig.
5
Positioning the appliance
Note:Do not use silicone to bond the appliance to
the worktop.
1. Position the hob with the upper side facing down
on a flat, stable surface.
2. Apply the adhesive seal supplied to the lower
edge of the hob. The adhesive seal prevents the
penetration of liquids.
→Fig.
6
3. Screw the brackets supplied into the specified po-
sition so that they can turn freely.
→Fig.
7
4. Turn the hob around and insert it into the recess.
Insert the hob in the right-hand side of the recess.
→Fig.
8
5. Turn the brackets and tighten them fully.
→Fig.
9
The position of the brackets depends on the work-
top thickness.
Removing the appliance
1. Disconnect the appliance from the electricity and
gas connections.
2. Unscrew the brackets and proceed in reverse or-
der.
Connecting the gas
Observe the country-specific guidelines.
Bekijk gratis de handleiding van Bosch POP6B6K30, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Bosch |
| Model | POP6B6K30 |
| Categorie | Fornuis |
| Taal | Nederlands |
| Grootte | 4731 MB |
