Handleiding
Je bekijkt pagina 7 van 36
7
tion. For conversion work to a different gas type,
we recommend that you call the after-sales ser-
vice.
¡ Ensure that the kitchen is sufficiently ventilated, in
particular when operating the gas cooking appli-
ance.
¡ Do not connect the appliance to an exhaust gas
system for combustion products.
¡ Never install the appliance in boats or in vehicles.
¡ The warranty applies only when using the appli-
ance as intended.
¡ Before installing the appliance, check that the
local conditions of the supplier are compatible
with the appliance settings specified on the rating
plate (type of gas and pressure, power, voltage).
¡ Secure the power cord to the cabinet to prevent it
from touching hot parts of the oven or hob.
¡ Before any work is carried out on the appliance,
switch off the power supply and the gas supply.
¡ Connect the appliance to the power supply using
the earth.
¡ Do not make any changes to the inside of the ap-
pliance. If required, contact our technical cus-
tomer service.
Before installing
¡ This appliance is a class 3 appliance in accord-
ance with the EN 30-1-1 standard for gas appli-
ances: Built-in appliance.
¡ The unit in which the appliance is installed must
be stable and secured appropriately.
¡ The units in the vicinity of the appliance, the lamin-
ated panels and the adhesive with which they are
secured must be made of non-flammable, heat-
resistant materials.
¡ Do not install this appliance above refrigerators,
washing machines, dishwashers or similar.
¡ The appliance must only be installed on an oven
with forced ventilation. Check the dimensions of
the oven in the installation instructions for the
oven.
¡ If you install an oven underneath the hob, the work
surface thickness may differ from the dimensions
given in these instructions. Take note of the in-
formation in the oven installation instructions.
¡ If you install an exhaust air fan or an extractor
hood, refer to the installation instructions for these.
Always observe the minimum vertical distance to
the hob.
→Fig.
1
Preparing the units
¡ Make a cut-out in the worktop with the required di-
mensions.
→Fig.
2
¡ Any panel that is attached closer to the built-in
niche than the specified clearance must be made
of non-combustible material. Always maintain a
distance of at least 5mm between the panel and
the appliance. Maximum clearances for the panel:
30 mm thickness x 70 mm height.
¡ Seal the cut surfaces of wooden work surfaces
with a special glue seal to protect them from mois-
ture.
WARNING‒Risk of burns!
The accessible parts may become hot during opera-
tion.
If there is no built-in oven underneath the hob and
the underside of the hob is accessible, follow these
instructions:
For gas hobs with wok burner, insert a non-flamable
intermediate floor (e.g. metal or ply-Wood) at a dis-
tance of 10 mm from the hob .
→Fig.
3
For gas hobs without a wok burner, it is advisable to
fit an intermediate floor underneath the hob .
→Fig.
4
In both cases, the distance from the intermediate
floor to the mains connection for the appliance must
be at least 10 mm.
The thickness of the separator must allow for re-
specting the distances in the figure.
Installation above an oven
→Fig.
5
Positioning the appliance
Note:Do not use silicone to bond the appliance to
the worktop.
1. Position the hob with the upper side facing down
on a flat, stable surface.
2. Apply the adhesive seal supplied around the edge
of the recess on the work surface. The adhesive
seal prevents the penetration of liquids.
→Fig.
6
3. Screw the brackets supplied into the specified po-
sition so that they can turn freely.
→Fig.
7
4. Turn the hob around and insert it into the recess.
Insert the hob in the front of the recess.
→Fig.
8
5. Turn the brackets and tighten them fully.
→Fig.
9
The position of the brackets depends on the work-
top thickness.
Removing the appliance
1. Disconnect the appliance from the electricity and
gas connections.
2. Unscrew the brackets and proceed in reverse or-
der.
Connecting the gas
Observe the country-specific guidelines.
CAUTION‒Risk of explosion!
A gas leakage may cause an explosion.
▶
If any connection is handled, check the seal.
¡ Arrange the gas connection so that the shut-off
valve is accessible.
¡ Ensure that the information on the rating plate re-
garding the gas type and gas pressure complies
with the local connection conditions.
¡ Connect the appliance to a fixed gas pipe or a
flexible metal pipe.
¡ The flexible metal pipe must not come into contact
with the moving parts of the unit in which the ap-
pliance is installed (e.g. a drawer) and must not
be routed through any spaces which might be-
come obstructed.
¡ Gas connection elbow on the appliance: R 1/2.
¡ Do not move or twist the gas connection elbow.
Connection to gas cylinder or liquid gas tank
▶
If the flame is large or unstable, check that the
regulator of the gas cylinder or liquid gas tank is
working properly.
Bekijk gratis de handleiding van Bosch PBP6B6K80, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Bosch |
| Model | PBP6B6K80 |
| Categorie | Fornuis |
| Taal | Nederlands |
| Grootte | 5284 MB |
