Bosch GSS 18V-10 Professional handleiding

Niet gecategoriseerd

Bosch

203 pagina's

PDF beschikbaar

Handleiding

/ 203

Je bekijkt pagina 15 van 203

is discharged, the power tool is switched off by means of a

protective circuit: The application tool no longer rotates.

u Do not continue to press the On/Off switch after the

power tool has automatically switched off. The battery

can be damaged.

To remove the battery (11), press the release button (12)

and pull the battery sideways out of the power tool. Do not

use force to do this.

Follow the instructions on correct disposal.

Fitting the base plate (see figure A)

Unscrew the four screws (14) completely. Fit a suitable base

plate and retighten the screws.

Changing the sanding plate (see figure A)

If necessary, the sanding plate (3) can be replaced.

Unscrew the four screws (14) completely and remove the

sanding plate (3). Fit the new sanding plate (3) and

retighten the screws.

Changing the sanding sheet

Remove dirt and dust from the sanding plate (3), e.g. with a

brush, before attaching a new sanding sheet.

To ensure optimum dust extraction, make sure that the

punched holes in the sanding sheet are aligned with the

drilled holes in the sanding plate.

Sanding sheets without hook-and-loop backing (see

figures B–D)

❶

Unlock both sanding-sheet clamps (4) and swivel them

downwards.

❷

Insert the sanding sheet (6) under the rear clamping

bracket (2). Ensure that the sanding sheet (6) is not too

short and that it is correctly clamped. Swivel the sand-

ing-sheet clamp (4) back into the starting position and

lock it in place.

❸ Position the sanding paper so that it fits tightly around

the sanding plate (3). Clamp the front part of the sand-

ing sheet under the front clamping bracket (7). Ensure

that the sanding sheet (6) is not too short and that it is

correctly clamped. Swivel the sanding-sheet clamp (4)

back into the starting position and lock it in place.

Unperforated sanding sheets, e.g. from rolls or bulk stock

sold by the metre, can be perforated using the punch (19)

for the purpose of dust extraction. To do this, fit the sanding

sheet on the power tool and push the tool down onto the

punch (see figureG).

To remove the sanding sheet (6), unlock both sanding-sheet

clamps (4) and pull the sanding sheet out of its bracket.

Selecting a sanding sheet

Different sanding sheets are available, depending on the ma-

terial you are working with and the required surface removal

rate:

Grit

40–180

Grit

For processing all wood and wood-based ma-

terials

For pre-sanding, e.g. of rough and un-

even beams and boards

Coarse 40

For surface sanding and levelling of

slight irregularities

Medium 80, 120

For finish-sanding and fine sanding of

hardwoods

Fine 180

For processing paint and lacquer layers or

primers such as fillers and bodyfillers

40–180

For sanding down paint Coarse 40

For sanding undercoats Medium 80, 120

For final sanding of primers prior to

painting

Fine 180

For any finishing work, such as polishing (metal and stone in

particular), use fleece/polishing felt.

Different types of fleece and polishing felts should be used

depending on the surface finish required on the workpiece.

Dust/chip extraction

The dust from materials such as lead paint, some types of

wood, minerals and metal can be harmful to human health.

Touching or breathing in this dust can trigger allergic reac-

tions and/or cause respiratory illnesses in the user or in

people in the near vicinity.

Certain dusts, such as oak or beech dust, are classified as

carcinogenic, especially in conjunction with wood treatment

additives (chromate, wood preservative). Materials contain-

ing asbestos may only be machined by specialists.

– Use a dust extraction system that is suitable for the ma-

terial wherever possible.

– Provide good ventilation at the workplace.

– It is advisable to wear a P2 filter class breathing mask.

The regulations on the material being machined that apply in

the country of use must be observed.

u Avoid dust accumulation at the workplace. Dust can

easily ignite.

Self-generated dust extraction with dust box (see figures

E1–E4)

Place the dust box (1) onto the extraction outlet (15) until it

clicks into place.

To empty the dust box (1), pull the dust box downwards.

Before opening the dust box (1), knock the dust box against

a firm surface as shown in the figure to loosen the dust from

the filter element.

Take hold of the dust box (1) by the recessed grip, fold the

filter element (16) upwards out of the way and empty the

dust box. Use a soft brush to clean the flaps of the filter ele-

ment (16).

English | 15

Bosch Power Tools 1 609 92A 4AB | (18.05.2018)

/ 203

Bekijk gratis de handleiding van Bosch GSS 18V-10 Professional, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.