Bosch GRC 12V-60 1/2 SN Professional handleiding

Niet gecategoriseerd

Bosch

163 pagina's

PDF beschikbaar

Handleiding

14 | English

Vibration total values a

(triax vector sum) and uncertainty K

determined according toEN62841-2-2:

Screwdriving: a

=2.3m/s

, K=1.5m/s

The vibration level and noise emission value given in these

instructions have been measured in accordance with a

standardised measuring procedure and may be used to com-

pare power tools. They may also be used for a preliminary

estimation of vibration and noise emissions.

The stated vibration level and noise emission value repres-

ent the main applications of the power tool. However, if the

power tool is used for other applications, with different ac-

cessories or is poorly maintained, the vibration level and

noise emission value may differ. This may significantly in-

crease the vibration and noise emissions over the total work-

ing period.

To estimate vibration and noise emissions accurately, the

times when the tool is switched off or when it is running but

not actually being used should also be taken into account.

This may significantly reduce vibration and noise emissions

over the total working period.

Implement additional safety measures to protect the oper-

ator from the effects of vibration, such as servicing the

power tool and accessories, keeping their hands warm, and

organising workflows correctly.

Rechargeable battery

Bosch sells some cordless power tools without a re-

chargeable battery. You can tell whether a rechargeable bat-

tery is included with the power tool by looking at the pack-

aging.

Charging the battery

u Use only the chargers listed in the technical data. Only

these chargers are matched to the lithium-ion battery of

your power tool.

Note: Lithium-ion rechargeable batteries are supplied par-

tially charged according to international transport regula-

tions. To ensure full rechargeable battery capacity, fully

charge the rechargeable battery before using your tool for

the first time.

Inserting the Battery

Push the charged battery into the battery holder until it

clicks into place.

Removing the Battery

To remove the rechargeable battery, press the battery re-

lease buttons and pull the battery out. Do not use force to

do this.

Battery charge indicator

The three green LEDs on the battery charge indicator indic-

ate the state of charge of the rechargeable battery. The bat-

tery charge indicator only lights up for five seconds after

start-up.

LED Capacity

3×continuous green light 68–100%

2×continuous green light 22–68%

1×continuous green light 2–22%

1×flashing green light 0–2%

Recommendations for Optimal Handling of the

Battery

Protect the battery against moisture and water.

Only store the battery within a temperature range of −20 to

50°C. Do not leave the battery in your car in the summer, for

example.

A significantly reduced operating time after charging indic-

ates that the battery has deteriorated and must be replaced.

Follow the instructions on correct disposal.

Assembly

u Before carrying out any work on the power tool (e.g.

maintenance, tool change etc.), remove the battery

from the power tool. There is risk of injury from uninten-

tionally pressing the on/off switch.

Changing the tool (see figure A)

u When fitting an application tool, make sure that it is

held securely in the tool holder. If the application tool is

not held securely in the tool holder, it may become loose

and consequently uncontrollable.

Slide the application tool (10) onto the square drive of the

tool holder (1).

Operation

u Only apply the power tool to the screw/nut when the

tool is switched off. Rotating tool inserts can slip off.

Setting the Rotational Direction (see figureB)

u The head of the ratchet wrench and the rotational dir-

ection switch can become hot during operation. There

is a risk of burns in the event of contact. Allow the

ratchet wrench to cool.

The rotational direction switch (2) is used to change the ro-

tational direction of the power tool. However, this is not pos-

sible while the on/off switch (7) is being pressed.

Clockwise: To drive in screws and tighten nuts, turn the ro-

tational direction switch(2) anticlockwise.

Anti-clockwise rotation: To loosen or unscrew screws and

nuts, turn the rotational direction switch (2) clockwise.

Switching on/off

Note: Unlock the on/off switch(7) by pushing the lock-off

button(8) upwards (see figureC).

To start the power tool, press and hold the on/off switch

(7).

1 609 92A C5Y | (08.05.2025) Bosch Power Tools

Bekijk gratis de handleiding van Bosch GRC 12V-60 1/2 SN Professional, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.