Bosch GPH 18V-60 Professional handleiding

Niet gecategoriseerd

Bosch

243 pagina's

PDF beschikbaar

Handleiding

/ 243

Je bekijkt pagina 17 van 243

English | 17

Operation

Preparations for Pressing and Pressing Process

u Only insert the rechargeable battery into the power

tool just before starting the pressing process. If, for

example, you inadvertently press the on/off button(13)

during the preparations for pressing, there is a risk of in-

jury.

u Never operate the power tool without inserting the

press insert. Otherwise, the power tool may become

damaged.

u In order to prevent the power tool from overheating,

do not use the power tool in continuous operation for

more than 15minutes. The power tool is not designed

for continuous operation.

Preparations for Pressing:

– Ensure that there is sufficient lighting at the place of use.

– You can turn the press head(3) in order to align it suit-

ably with the insertion position.

– Open the press head(3) by pressing the unlocking

lever(1). Position the press head at a right angle to the

connector to be pressed. Ensure that there are no foreign

objects between the press insert and the connector.

– Close the press head(3) and ensure that you hear the un-

locking lever(1) click into place.

Pressing Process:

– Insert the rechargeable battery into the power tool.

– To switch on and start the pressing process, press and

hold the on/off button(13). The worklight(11) lights up.

– Once the maximum pressing force has been reached, the

piston rod(5) will move back with the press insert and

the motor will switch off automatically. Release the on/

off button(13). The worklight will go out automatically

after approx. 10s.

Manually Ending the Pressing Process:

– To end the pressing process prematurely, release the on/

off button(13) during the pressing process. The pressing

process stops.

– If the pressing process stops prematurely or the piston

rod(5) does not move back automatically after the end of

the pressing process, press the reset button(6). Hold the

reset button down until the piston rod has moved back

into the starting position.

Remove the battery from the power tool. Open the press

head(3) by pressing the unlocking lever(1) and pull the

power tool away from the connector.

If the status indicator(7) lights up green at the end of the

pressing process, the maximum pressure has been reached.

If the status indicator lights up red, check the pressing and,

if necessary, repeat the processing process.

Sleep Mode and Restart Protection

For safety reasons, the power tool will be put into sleep

mode in the following cases:

– If more than 5mins have passed since the battery was in-

serted or the tool has not been used for more than 5mins

after the last pressing process,

– If the on/off button(13) is pressed while the battery is

being inserted (as restart protection).

In this case, briefly press the on/off button(13) once to ac-

tivate the power tool. Then start the pressing process as

usual.

Status indicators

Colour of the status

indicator(7)

Meaning Corrective measure

After Inserting the Battery/Waking the Tool up from Sleep Mode:

Green (3s) Power tool ready for use −

Yellow (3s) There are fewer than 1000work cycles re-

maining until the end of the maintenance

interval.

Schedule maintenance with an authorisedBosch

after-sales service centre.

Red (3s) Battery is too weak for pressing process Charge/change battery

Battery and/or power tool outside the op-

erating temperature range

Allow the battery and the power tool to reach the

correct temperature range

After Completion of the Pressing Process/During Operation:

Green (3s) Pressing force target value reached, la-

bour value OK

−

Yellow (continuous) Maintenance interval of 20,000work

cycles exceeded

Send the power tool to an authorisedBosch after-

sales service centre for maintenance.

Red (3s) Pressing force not reached, internal power

tool error or power tool outside the oper-

ating temperature range

1. Restart the pressing process

2. Remove and reinsert the battery

3. Allow the power tool to reach the correct tem-

perature range

Bosch Power Tools 1 609 92A B10 | (22.11.2024)

/ 243

Bekijk gratis de handleiding van Bosch GPH 18V-60 Professional, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.