Bosch GKS 130 Professional handleiding
Handleiding
Je bekijkt pagina 9 van 68
English | 9
(25)
Dust extraction adapter
a)
a)
Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
b)
Commercially available (not included in the scope of deliv-
ery)
Technical data
Hand-held circular saw GKS 130
Article number
3601FC30..
Rated power input W 1300
No-load speed min
–1
5800
Max. cutting depth with 184mm saw blade diameter
– at a 0° mitre/bevel angle mm 64
– at a 45° mitre/bevel angle mm 45
Spindle lock ●
Base plate dimensions mm 290 x 150
Max. saw blade diameter mm 184
Min. saw blade diameter mm 184
Max. base blade thickness mm 2.0
Locating bore mm 20
Weight according to
EPTA-Procedure01:2014
kg 3.9
Protection class
/ II
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Fitting
u Only use saw blades the maximum permitted speed of
which is higher than the no-load speed of the power
tool.
Inserting/changing the circular saw blade
u Pull the plug out of the socket before carrying out any
work on the power tool.
u Wear protective gloves when fitting the saw blade.
Danger of injury when touching the saw blade.
u Do not use abrasive wheels as the application tool un-
der any circumstances.
Removing the saw blade (see figure A)
To change tools, we recommend that you place the power
tool down on the front side of the motor housing.
– Press and hold the spindle lock button (4).
u Do not press the spindle lock button (4) while the saw
spindle is moving. The power tool may become damaged
if this happens.
– Use the hex key (17) to undo the clamping bolt (18) in ro-
tational direction ➊.
– Swing the retracting blade guard (11) back and hold on
to it firmly.
– Remove the clamping flange (19) and the saw blade (20)
from the saw spindle with mounting flange (21).
Selecting the saw blade
You will find an overview of recommended saw blades at the
end of these operating instructions.
Fitting the Saw Blade (see figure A)
To change tools, we recommend that you place the power
tool down on the front side of the motor housing.
– Clean the saw blade (20) and all the clamping elements
to be fitted.
– Swing the retracting blade guard (11) back and hold on
to it firmly.
– Place the saw blade (20) on the saw spindle with mount-
ing flange (21). The cutting direction of the teeth (direc-
tion of the arrow on the saw blade) must match the rota-
tional direction of the arrow on the protective guard (15).
– Attach the clamping flange (19) and screw in the clamp-
ing bolt (18) in rotational direction ➋. Ensure that the
saw spindle with mounting flange (21) and clamping
flange (19) are installed in the correct position.
– Press and hold the spindle lock button (4).
– Use the hex key (17) to tighten the clamping bolt (18) in
rotational direction ➋. The tightening torque should be
6–9Nm, which corresponds to hand-tight plus ¼ turn.
Dust/chip extraction
The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
tions and/or cause respiratory illnesses in the user or in
people in the near vicinity.
Certain dusts, such as oak or beech dust, are classified as
carcinogenic, especially in conjunction with wood treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be machined by specialists.
– Use a dust extraction system that is suitable for the ma-
terial wherever possible.
– Provide good ventilation at the workplace.
– It is advisable to wear a P2 filter class breathing mask.
The regulations on the material being machined that apply in
the country of use must be observed.
u Avoid dust accumulation at the workplace. Dust can
easily ignite.
Fitting the dust extraction adapter (see figure E)
Push the dust extraction adapter (25) onto the chip ejector
(14) until it clicks into place.
A dust extraction hose with a diameter of 35mm can be con-
nected to the dust extraction adapter (25).
u The dust extraction adapter must only be fitted if an
external dust extraction system is connected. Other-
wise the extraction duct can become clogged.
u No dust bags should be connected to the dust extrac-
tion adapter. Otherwise the extraction system can be-
come clogged.
Bosch Power Tools 1 609 92A 8C7 | (16.11.2022)
Bekijk gratis de handleiding van Bosch GKS 130 Professional, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Bosch |
| Model | GKS 130 Professional |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 13835 MB |
