Bosch GCS 18V-230 Professional handleiding

Niet gecategoriseerd

Bosch

323 pagina's

PDF beschikbaar

Handleiding

/ 323

Je bekijkt pagina 23 van 323

English | 23

u The protective guard(5) must only be able to be ro-

tated in the direction of the accessory while the ad-

justing lever(7) is actuated. Otherwise, the power

tool must not be used any more under any circum-

stances and must be sent to the after-sales service.

Operation

Starting Operation

Switching On and Off (seefigureG)

To start the power tool, first press the lock-off switch(2),

then press and hold the on/off switch(1).

To switch off the power tool, release the on/off switch(1).

Note: For safety reasons, the on/off switch(1) cannot be

locked; it must remain pressed during the entire operation.

Opening/Closing the Water Supply (seefigureH)

To open the water supply, put the valve(16) into position I:

Water will flow continuously over the diamond cutting disc.

To close the water supply, put the valve(16) into the OFF

position.

Switching On the Worklight (seefigureI)

The worklight(19) will light up when the on/off switch(1) is

fully pressed. The worklight will remain lit for approx.

5seconds after the on/off switch(1) has been released.

Overload protection

The power tool is equipped with an overload protection sys-

tem. In the event of overloading, the power tool automatic-

ally shuts off the electronics and the worklight(19) and the

status indicator(21) flash.

To switch the tool back on: Release the on/off switch(1).

As soon as the worklight(19) is no longer flashing and the

status indicator(21) lights up green, you can switch the

power tool back on.

Status indicator

(seefigureD)

The status indicator(21) indicates the status of the power tool according to the table below.

Status indicator(21) Cause Solution

Green Power tool is ready for operation –

Yellow A battery with a capacity lower than 8.0Ah is

used; the power tool can be used with reduced

power

Use a battery with a capacity of at least 8.0Ah

Battery is almost empty Replace or charge battery

Power tool and/or battery are exceeding the

permissible operating temperature

Run the power tool at no load and allow it to

cool down; allow the battery to cool down (see

"Technical Data", page20)

Red (continuous) and LED

worklight flashing

Power tool and/or battery have exceeded the

permissible operating temperature

Run the power tool at no load and allow it to

cool down; allow the battery to cool down (see

"Technical Data", page20)

Replace the battery

Power tool is being overloaded End the overload state and, if necessary,

switch the power tool back on. Remove the bat-

tery and reinsert it. Then turn the power tool on

again

Red (continuous) Internal error Remove the battery and reinsert it. Then turn

the power tool on again

Send the power tool to an authorised after-

sales service centre for Bosch power tools

Battery is empty Replace or charge battery

Cutting disc is jammed Release the on/off switch, remove the cutting

disc from the workpiece and restart the applic-

ation.

Flashing red, LED worklight

flashing and the power tool

does not start up

On/off switch was pressed while the battery

was being inserted

Release the on/off switch and continue insert-

ing the battery. Once the battery is fully inser-

ted, close the cover of the battery compart-

ment. Release the on/off switch (by pressing

the lock-off switch) and then press the on/off

Bosch Power Tools 1 609 92A 3AM | (15.11.2024)

/ 323

Bekijk gratis de handleiding van Bosch GCS 18V-230 Professional, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.