Blizzard SnoKontrol handleiding
Handleiding
Je bekijkt pagina 9 van 20
Page 9
Snokontrol™ User Manual - Rev. A © 2020 Blizzard Lighting, LLC
3.OPERATING INSTRUCTIONS
3.1 Setup
3.1.1 Setting Up The System
Plug the power supply to the system back panel and to the mains outlet.
Plug in your DMX cable(s) to your intelligent lighting as described in the xtures
respective manual. For a quick lesson on DMX see the DMX Primer section in
the Appendix of this manual.
3.1.2 Fixture Addressing
This unit is capable of controlling 24 xtures, with up to 16 DMX channels per
xture, or 12 xtures with up to 32 channels of DMX per xture (using Page A
only, 32 channels apart).
*The table below shows data for 24 individual xtures with up to 16 channels of DMX each. For xtures
that require up to 32 DMX channels (up to 12 xtures total), assign the starting addresses that correspond
with those of Page A (1-16), and they will continue on Page B (17-32).
Fixture
Page
Button
SCAN
Button
DMX
Start
Address
DIP Switch
Settings (SET
TO ON)
Fixture
Page
Button
SCAN
Button
DMX
Start
Address
DIP Switch
Settings (SET
TO ON)
1 A 1 001 1 13 A 7 193 1, 7, 8
2 B 1 017 1, 5 14 B 7 209 1, 5, 7, 8
3 A 2 033 1, 6 15 A 8 225 1, 6, 7, 8
4 B 2 049 1, 5, 6 16 B 8 241 1, 5, 6, 7, 8
5 A 3 065 1, 7 17 A 9 257 1, 9
6 B 3 081 1, 5, 7 18 B 9 273 1, 5, 9
7 A 4 097 1, 6, 7 19 A 10 289 1, 6, 9
8 B 4 113 1, 5, 6, 7 20 B 10 305 1, 5, 6, 9
9 A 5 129 1, 8 21 A 11 321 1, 7, 9
10 B 5 145 1, 5, 8 22 B 11 337 1, 5, 7, 9
11 A 6 161 1, 6, 8 23 A 12 353 1, 6, 7, 9
12 B 6 177 1, 5, 6, 8 24 B 12 369 1, 5, 6, 7, 9
Please refer to your individual xture’s manual for detailed DMX addressing
instructions. The table above refers to a standard 9-DIP Switch binary congu-
rable device.
3.1.3 Pan & Tilt Channels
Because not all intelligent lighting xtures are alike or share the same control
attributes, the Controller allows the user to assign the correct pan and tilt chan-
nel for every individual xture.
1. Hold <PROGRAM> + <TAPSYNC DISPLAY> until the display ashes.
2. Press the <SCANNER> or <PAGE SELECT> button that represents the
xture whose faders you would like to reassign.
3. Move the pan channel fader of the the selected xture.
4. Press the <TAPSYNC DISPLAY> button to conrm.
5. Move the tilt channel fader of the the selected xture.
6. Hold <PROGRAM> + <TAPSYNC DISPLAY> until the display ashes.
Bekijk gratis de handleiding van Blizzard SnoKontrol, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Blizzard |
| Model | SnoKontrol |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 2469 MB |
