Blizzard HotStik 5 COB II handleiding

Handleiding

1234567891011121314151617181920/ 20

Afdrukken

Je bekijkt pagina 11 van 20

Page 11

HotStik 5™ COB II User Manual Rev. B Copyright © 2019 Blizzard Lighting, LLC

EachwiCICLE

®

acts as both a transmitter and a receiver, depending on whether

a DMX source is applied to the integral XLR connector. This is an extremely

powerful feature of the system, however, it also requires 1 piece of due dili-

gence, and that is the removal of extraneous DMX signals from your lighting rig

BEFOREproceeding.

SO: BEFORE DOING ANYTHING ELSE, YOU SHOULD DISABLE ANY

BUILT-IN PROGRAMS IN THE FIXTURES YOU WISH TO CONNECT AND/

OR SET THEM AS SLAVES PRIOR TO RETURNING THEM TO DMX MODE

(IF APPLICABLE). Most xtures contain a built-in automatic, sound

active or custom program which is designed to operate with the xture

NOT connected to a DMX chain.

Someoftheseprogramswillautomaticallyrununlessthextureissettoslave

mode.ThesexturestypicallysenseDMXautomaticallyandswitchtoDMX

mode upon receiving DMX signal (our Pucks do that!)

IfyouplugawiCICLE

®

“receiver”intoanautosensingxturesetasa“mas-

ter,“chancesaregoodthatthewiCICLE

®

“receiver” will begin transmitting the

master program. Most times, this is undesirable, and taking the two seconds to

switchtheseprogramsowillsolvealotofails.

Got that done? Good! Then let’s proceed!

1.PlugthewiCICLE

®

Receiverintothe“DMXIN”connectorofthextureand

verify it is receiving power (the STATUS LED should illuminate.)

2.ConnecttheAC/DCadaptortothewiCICLE

®

Transmitter and verify it is re-

ceiving power (the STATUS LED should illuminate.)

3. Press the RECESSED SELECTOR BUTTON on the Transmitter to select the

operating channel group. (The system will store this setting for future use)

The7-ColorStatusLEDwillchangecolortoindicatethecurrentchannelgroup:

· GROUP 1: RED

· GROUP 2: GREEN

· GROUP 3: YELLOW

· GROUP 4: BLUE

· GROUP 5: VIOLET

· GROUP 6: CYAN

· GROUP 7: WHITE

4. Follow the same procedure on the Receiver to select the channel group.

5. Once both the transmitter and receiver(s) are both set to the same chan-

nel group, connect the transmitter to the DMX controller or the DMX out of a

xtureonyourDMXchain.

6.OnceaDMXsignalisprovidedtothetransmitter,thestatusLEDwillblink

RED slowly until communication is established with the receiver. The status

LEDonthereceiver(s)willashGREEN slowly until communication is estab-

lished.

7.Oncetheclearestchannelisauto-selected,thestatusLEDswillblinkquickly

onboththetransmitterandreceiver.NOTE:ThecoloroftheLEDDURING

operation does not indicate channel group, instead it indicates whether the

unit is transmitting or receiving. That’s It!

NOTE: “GROUP” number

also corresponds to the

“GROUP” setting on our

LightCaster™ wireless DMX

Transceiver.

1234567891011121314151617181920/ 20

Bekijk gratis de handleiding van Blizzard HotStik 5 COB II, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.

Productinformatie

Gerelateerde producten van Blizzard (Niet gecategoriseerd)

Handleiding bekijken

Blizzard Outpost Ranger RGBALC

Niet gecategoriseerd - handleiding

Handleiding bekijken

Blizzard Outpost RGBALC

Niet gecategoriseerd - handleiding

Andere merken in Niet gecategoriseerd