Biltema 21-9506 handleiding
Handleiding
Je bekijkt pagina 3 van 16
3
© 2024-11-04 Biltema Nordic Services AB
Art. 21-9505, 21-9506, 21-9507
SE
melodivalsknappen. Enheten är nu återställd.
2. Para ihop enheterna genom att hålla melodivalsk-
nappen intryckt tills mottagaren låter ”Ding-Ding”.
Tryck då på tryckknappen på sändaren. När
mottagaren låter ”Ding” är sammankopplingen
klar. Tryck därefter på melodivalsknappen för att
lämna parningsläget. Nu kan du börja använda
dörrklockan.
3. Ändra melodi genom att trycka på melodivalsk-
nappen (30 st).
MOTTAGARE BATTERIDRIVEN, 21-9506
Wireless Battery Operated Doorbell
Model No.: FLD-536P(219506)
Fig. 2
Fig. 7
Bell push button
Adhesive
Tape
Screws
Fig.1
Kinetic bell
Push button
Receiver unit
How to Pairing:
The transmitter and receiver have been pairing during the
packaging. If your doorbell is not working well. You can follow up
below 3 steps to reset the product.
1.Clear the pairing codes inside the receiver. Firstly, press /hold
the "melody selection button", then install the final battery into
the battery compartment, hold to press the button for about 8
seconds, you will see the receiver's LED flashing, then release
the button, the codes are all removed from the internal memory.
2.Pairing the transmitter and receiver again. Press/hold the
"melody selection button" on the receiver about 4 seconds, and
release the button until you hear "Ding-Ding" sound, then press
the transmitter, now you will hear the receiver play "Ding" sound,
you can wait for another "Ding-Ding" sound or press the "melody
selection button" directly to exit the paring mode. Like Fig5
3.Press the transmitter and test if pairing is completed, then enjoy
the use of our product again.
Features:
1. Bell push button uses kinetic technology, no battery required.
2. Transmitter is with LED and IP65 waterproof.
3. Receiver powered by 3x1.5V AA batteries (Not Included)
4. LED indicator in the receiver.
5. Receiver is with 32 melodies and 4 level volume control.
6. 100M operating range in the open air.
7. Self-learning technology avoid interference.
Installation:
The transmitter can be mounted on door frame.
The chime can be put on table or mounted on wall.
Fig. 4
Fig. 5
Music Selection/
Pairing Button
Fixing Point
Removable Battery Cover
(Requires 3x1.5V AA Batteries)(not included)
På framsidan av mottagaren sitter högtalaren och på
ovansidan nns knappar för volymkontroll och val av
ljud/melodi. Knappen för val av melodi används även
för att para ihop mottagare och sändare.
På baksidan hittar du batterifacket, ta av locket
genom att placera tummarna på de räf ade ytorna
och dra locket neråt. Sätt i 3 x AA-batterier enligt
polaritetsanvisningarna. På baksidan nns även ett
hål med ett spår i för skruvhuvudet, se g 5 ( xing
point). Skruva inte skruven hela vägen in i väggen
utan låt skruvhuvudet sticka ut några millimeter så
att det passar i spåret på baksidan av sändaren. Om
du inte vill skruva fast mottagaren kan du ha den löst
liggande var du vill.
Receiver
Bell push button
Fig. 2
Adhesive
Tape
Screws
Fig.1
Kinetic bell
Push button
EU Plug
Fig. 4
Fig. 5
Fig. 3
Features:
1. Bell push button uses kinetic technology, no battery required.
2. Transmitter is with LED and IP65 waterproof.
3. Receiver is power by 110V~240V/50Hz,
with EU plug.
4. LED indicator in the receiver.
5. Receiver is with 32 melodies and 4 level volume control.
6. 100M operating range in the open air.
7. Self-learning technology avoid interference.
Installation:
The transmitter can be mounted on door frame.
The chime should be plugged into the socket for main
power supply.
How to Pairing:
The bell push button and receiver have been pairing during the
packaging. If your doorbell is not working well. You can follow up
below 3 steps to reset the product.
1. Clear the pairing codes inside of the receiver. Firstly, press and
hold the "melody selection button", and plug it into the socket until
you see the receiver's LED flashing and hear the sound, then release
the button, reset is complete.
2. Pairing the bell push button and receiver. Press and hold the
"melody selection button" until you hear "Ding-Ding" sound, press
the bell push button and you will hear the receiver play "Ding" sound,
press the "melody selection button" to exit the paring mode, now
you can start using the doorbell.
3. Change melody: press the "melody selection button" to select
your desired melody.
Model No.: FLP-535P-E(219505)
Wireless Plug-In Doorbell
Speaker
Sound Selection/
Pairing Button
Fig. 6
MOTTAGARE 220–240 V, 21-9505
Receiver
Bell push button
Fig. 2
Adhesive
Tape
Screws
Fig.1
Kinetic bell
Push button
EU Plug
Fig. 4
Fig. 5
Fig. 3
Features:
1. Bell push button uses kinetic technology, no battery required.
2. Transmitter is with LED and IP65 waterproof.
3. Receiver is power by 110V~240V/50Hz,
with EU plug.
4. LED indicator in the receiver.
5. Receiver is with 32 melodies and 4 level volume control.
6. 100M operating range in the open air.
7. Self-learning technology avoid interference.
Installation:
The transmitter can be mounted on door frame.
The chime should be plugged into the socket for main
power supply.
How to Pairing:
The bell push button and receiver have been pairing during the
packaging. If your doorbell is not working well. You can follow up
below 3 steps to reset the product.
1. Clear the pairing codes inside of the receiver. Firstly, press and
hold the "melody selection button", and plug it into the socket until
you see the receiver's LED flashing and hear the sound, then release
the button, reset is complete.
2. Pairing the bell push button and receiver. Press and hold the
"melody selection button" until you hear "Ding-Ding" sound, press
the bell push button and you will hear the receiver play "Ding" sound,
press the "melody selection button" to exit the paring mode, now
you can start using the doorbell.
3. Change melody: press the "melody selection button" to select
your desired melody.
Model No.: FLP-535P-E(219505)
Wireless Plug-In Doorbell
Speaker
Sound Selection/
Pairing Button
Fig. 6
På framsidan av mottagaren sitter högtalaren och på
baksidan nns en EU-plug för anslutning till nätuttag.
På sidan nns knappar för volymkontroll och val av
ljud/melodi. Knappen för val av melodi används även
för att para ihop mottagare och sändare.
Sammankoppling 219505
Enheterna är sammankopplade från fabrik. Om
enheterna inte fungerar som de ska behöver du göra
en återställning och en ny sammankoppling. Följ
nedanstående steg.
1. Håll melodivalsknappen intryckt samtidigt som
du kopplar in enheten i ett nätuttag. När mottaga-
rens lysdiod blinkar och ett ljud avges släpper du
Bekijk gratis de handleiding van Biltema 21-9506, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Biltema |
| Model | 21-9506 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 2122 MB |
