Berner Architectural Elite 10 handleiding

Niet gecategoriseerd

Berner

16 pagina's

PDF beschikbaar

Handleiding

-4-

II. MOUNTING INSTRUCTIONS (General)

INDOOR MOUNTING ONLY

To achieve optimum protection, the air curtain should be

mounted on the inside of the building, ush to the wall and

as close to the top of the door opening as possible. To ensure

peak performance, keep the air stream free of obstructions.

The air curtain will not perform properly if negative air

pressure exists in the building. Under these conditions,

a means for makeup air to the building must be provided

so that the air pressure on both sides of the opening is in

balance.

Before mounting the air curtain, check the supporting structure

to verify that it has sucient load-carrying capacity to support

the weight of the air curtain(s). The mounting hardware

(supplied by others) should be capable of supporting a

minimum of three (3) times the weight of the air curtain.

See Table 1.

IMPORTANT: A minimum of 4” is required above the top rear

corner of the air curtain for the installation and removal of the

inlet screen, and to ensure proper airow.

A. When determining the mounting location for the air

curtain(s), make sure that nothing interferes with the

curtain of air developed when the discharge vanes are

directed from 0° to 20° toward the door opening. If the

air stream strikes any obstruction (the top edge of the

doorway, a door opening device, etc.), the eectiveness

of the air curtain will be greatly reduced. See Figure 2.

B. For optimum performance, the bottom of the air curtain

(discharge nozzle) should be no more than 1” above the

top of the door opening with the air curtain(s) mounted

ush to the wall. If the air curtain must be mounted

higher, it must be spaced out from the wall 3/8” for

every inch the air curtain is above the door opening. See

Figure 3. For optimum protection, any void between the

air curtain and the wall should be sealed along the full

length of the air curtain.

C. Do not block (obstruct) the air intake screen. Insucient

airow can cause the unit to overheat.

D. The air curtain(s) shall:

1. Have a minimum clearance of at least 4” from

the sides and 4" from the top.

2. Have a minimum clearance of at least 6’ between

the bottom of the air curtain and the oor.

3. Be installed Indoors Only.

E. Proceed to either Section III - WALL MOUNTING or

Section IV - SUSPENDED MOUNTING

A. PREPARATION

1. Locate the wall mounting brackets. Two of the wall

mounting brackets are shipped already attached

to the back of the air curtain, and the third

is shipped loose and can be found in the carton that

contained the air curtain. See Figure 4.

Figure 2 - General Mounting

Figure 3 - Wall Mounting Location

TABLE 1 - Weight Chart

III. WALL MOUNTING

MODEL

Net Weight

MODEL

Net Weight

AE10

Ambient

AE10

Electric

AE10

Hot

Water

AE08

Ambient

AE08

Electric

AE08

Hot

Water

AE10-F-1036 100 104 125 AE08-F-1036 52 57 72

AE10-F-1042 112 116 140 AE08-F-1042 59 64 82

AE10-F-1048 125 129 156 AE08-F-1048 66 71 91

AE10-F-2060 168 176 205 AE08-F-1060 81 86 111

AE10-F-2072 193 201 239 AE08-F-1072 95 100 133

AE10-F-2084 218 226 270 AE08-F-2084 117 127 160

AE10-F-2096

244 252 302 AE08-F-2096 132 142 180

AE10-F-3096

262 274 320 AE08-F-2108 146 156 199

AE10-F-3108

287 299 351 AE08-F-2120 157 167 214

AE10-F-3120

306 318 374

AE10-F-3132

337 349 416

AE10-F-3144

362 374 447

AE10-F-4144

380 396 465

20°

AIR

Discharge

Nozzle

INTERIOR

EXTERIOR

6' minimum

AIR

Airstream

4" minimum

side & top

clearance from

combustible

material

AE08 - 7.125”

AE10 - 11”

AE08 - 10.75” MIN.

AE10 - 15” MIN.

WALL MOUNTING

BRACKET

MOUNTING

SCREWS

SPACER

MOUNTING

SCREWS

SEAL ALONG

LENGTH

Bekijk gratis de handleiding van Berner Architectural Elite 10, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.