Handleiding
Je bekijkt pagina 29 van 108
108108
Split type air conditioner / User Manual 29 / 108 EN
28 / 112 EN
Split Type Air Conditioner / User Manual
4.3 Outdoor Unit Installation
Install the unit by following local codes and
regulations , there may be differ slightly between
different regions.
evoba )ni42( mc06
60cm (24in)
on righ
t
30cm (12in)
on left
200cm (79in)
in fron
t
30cm (12in)
from back wall
30cm (12in) on left
60cm (24in) onright
60cm (24in) above
30cm (12in)
frombackwall
200cm (79in) infront
4.3.1 Installation Instructions – Outdoor
unit
Step 1: Select installation location
Before installing the outdoor unit, you must
choose an appropriate location. The following
are standards that will help you choose an
appropriate location for the unit.
Proper installation locations meet the
following standards:
• Meets all spatial requirements shown in Instal-
lation Space Requirements above.
• Good air circulation and ventilation
• Firm and solid—the location can support the
unit and will not vibrate
• Noise from the unit will not disturb others
• Protected from prolonged periods of direct
sunlight or rain
• Where snowfall is anticipated, raise the unit
above the base pad to prevent ice buildup and
coil damage. Mount the unit high enough to be
above the average accumulated area snowfall.
The minimum height must be 18 inches.
DO NOT install unit in the following
locations:
• Near an obstacle that will block air inlets and
outlets
• Near a public street, crowded areas, or where
noise from the unit will disturb others
• Near animals or plants that will be harmed by
hot air discharge
• Near any source of combustible gas
• In a location that is exposed to large amounts
of dust.
• In a location exposed to a excessive amounts
of salty air.
C
If the unit is exposed to heavy
wind: Install unit so that air
outlet fan is at a 90° angle
to the direction of the wind. If
needed, build a barrier in front
of the unit to protect it from
extremely heavy winds. See
Figures below.
Strong wind
Wind baffle
Strong
wind
Strong wind
C
If the unit is frequently exposed
to heavy rain or snow:
Build a shelter above the unit to
protect it from the rain or snow.
Be careful not to obstruct air
flow around the unit.
If the unit is frequently exposed
to salty air (seaside):
Use outdoor unit that is specially
designed to resist corrosion.
4 Installation
29 / 112 EN
Split Type Air Conditioner / User Manual
Step 2: Install drain joint (Heat pump unit only)
Before bolting the outdoor unit in place, you must
install the drain joint at the bottom of the unit.
Note that there are two different types of drain
joints depending on the type of outdoor unit.
If the drain joint comes with a rubber seal
(see Fig. A ), do the following:
1. Fit the rubber seal on the end of the drain joint
that will connect to the outdoor unit.
2. Insert the drain joint into the hole in the base
pan of the unit.
3. Rotate the drain joint 90° until it clicks in place
facing the front of the unit.
4. Connect a drain hose extension (not included)
to the drain joint to redirect water from the unit
during heating mode.
If the drain joint doesn’t come with a rubber
seal (see Fig. B ), do the following:
1. Insert the drain joint into the hole in the base
pan of the unit. The drain joint will click in place.
2. Connect a drain hose extension (not included)
to the drain joint to redirect water from the unit
during heating mode.
Seal
Drain joint
(A) (B)
Base pan hole of
outdoor unit
Seal
Base pan hole of outdoor
unit
Seal
Seal
Drain joint
4 Installation
A
CAUTION! In cold climates,
make sure that the drain hose is
as vertical as possible to ensure
swift water drainage. If water
drains too slowly, it can freeze in
the hose and flood the unit.
Step 3: Anchor outdoor unit
The outdoor unit can be anchored to the ground
or to a wall-mounted bracket with bolt(M10).
Prepare the installation base of the unit according
to the dimensions below.
C
The following is a list of
different outdoor unit sizes
and the distance between their
mounting feet. Prepare the
installation base of the unit
according to the dimensions
below.
A
B
D
Air inlet
Air outlet
Air inlet
W
H
Air inlet
Air inlet
Air outlet
Bekijk gratis de handleiding van BEKO BRVPF095, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | BEKO |
| Model | BRVPF095 |
| Categorie | Airco |
| Taal | Nederlands |
| Grootte | 10539 MB |
