Bauknecht WM Sense 9AA handleiding

Wasmachine

Bauknecht

14 pagina's

PDF beschikbaar

Handleiding

TROUBLESHOOTING

Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Service, make sure that the problem cannot be easily

solved using the following list.

Anomalies Possible causes / Solution

The washing machine does

not start.

The appliance is not plugged into the socket fully, or not enough to make contact.

There is no power in the house.

The wash cycle does not start.

The washing machine door is not closed properly.

The ON/OFF

button has not been pressed.

The START/PAUSE button has not been pressed.

The water tap has not been opened.

A delay has been set for the start time.

The Demo Mode is active (see below how to deactivate).

The washing machine does

not ll with water (“

”

appears on the display).

The water inlet hose is not connected to the tap.

The hose is bent.

The water tap has not been opened.

There is no water supply in the house.

The pressure is too low.

The START/PAUSE

button has not been pressed.

The washing machine

continuously loads and

unloads water.

The drain hose is not tted between 65 and 100 cm from the oor.

The free end of the hose is immersed in water.

The wall drainage system is not tted with a breather pipe.

If the problem persists even after these checks, turn o the water tap, switch the appliance o and contact the

Technical Assistance Service. If the home is on one of the upper oors of a building, there may be problems relating

to back-siphonage, causing the washing machine to ll with water and drain continuously. Special anti-siphon

valves are available in shops and help to prevent this inconvenience.

The washing machines does

not drain and the symbol

(F9E1) on the display.

Clean the pump lter (see Care and maintenance chapter)

The drain hose is bent.

The drainage duct is clogged.

The washing machine

vibrates a lot during the spin

cycle.

Transport bolts have been not removed correctly during installation.

The washing machine is not leveled.

The washing machine is tucked between furniture cabinets and the wall.

The washing machine leaks.

The water inlet hose is not screwed on properly.

The detergent dispenser drawer is obstructed.

The drain hose is not properly attached.

The

symbol blinks and the

display visualises an error

code (e.g.: F1E1, F4...).

Switch o the machine and unplug it, wait for approximately 1 minute and then switch it back on again.

If the problem persists, contact the Technical Assistance Service.

There is too much foam.

The detergent is not suitable for machine washing (it should display the text “for washing machines” or “hand and

machine wash”, or the like).

Too much detergent was used.

“Spin&Drain” phase icon

blinks, “0” spin speed

displayed .

Unbalance of laundry load prevented spin cycle, to protect the washing machine.

If you want to spin the wet laundry, add more laundry items of dierent sizes and start “Spin&Drain” programme.

Avoid small laundry loads consisting of few big, absorbent pieces of laundry / wash dierent sizes of articles in one

load.

Disable the DEMO MODE : The following actions must be carried out in sequence, without breaks. Switch the machine ON and then switch it OFF again. Press

the START/PAUSE

button until the buzzer is heard. Switch the machine on again. The “DEMO” indicator ashes and then turns OFF.

400011718032

xxxxxxxxxxxx

Policies, standard documentation, ordering of spare parts and additional product information can be found by:

• Using the QR code in your appliance

• Visiting our website http://docs.bauknecht.eu and parts-selfservice.whirlpool.com

• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When contacting our After-sales

Service, please state the codes provided on your product’s identication plate.

• For User’s Repair & Maintenance Information visit www.bauknecht.eu

The model information can be retrieved using the QR-Code reported in the energy label. The label also includes the model identier

that can be used to consult the portal of the registry at https://eprel.ec.europa.eu

Bekijk gratis de handleiding van Bauknecht WM Sense 9AA, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.