Bauknecht BCT11A9FHTSK handleiding
Handleiding
Je bekijkt pagina 37 van 84
hollow areas.
FISH (whole): Position the tip in the thickest part,
avoiding the thorns.
BAKERY & PASTA: Insert the tip deep into the dough
by shaping the cable to achieve the optimum
probe angle. It is required to use the compatible
AUTO MODES functions in order to perform a probe
controlled cooking for these food types. If you use
the probe when cooking with the AUTO MODES
functions, cooking will be stopped automatically
when the selected recipe reaches the ideal core
temperature, without the need to set the oven
temperature.
DESCALE
This special function, activated at regular intervals,
allows you to keep the steam system in the best
condition. Once the function is started, follow all the
steps indicated on the display.
The duration of the full function may take up to 120
minutes and cannot be stopped.
Descale can be started anytime by the user from the
Cleaning Menu.
The display will show you when it is time to run a
Descale cycle (see the table below).
DESCALE MESSAGE MEANING
<DESCALE RECOMMENDED>
It appears after around 15
hours of steam cycles*
It is recommended to run a
Descale cycle.
<DESCALE NEEDED>
It appears after around 20
hours of steam cycles*
Descale is mandatory. It is not
possible to run a Steam cycle
until a Descale cycle will be
carried out.
*considering the default value (4 - Hard) of water
hardness level. The number of hours of steam cycles
that must pass before the Descale messages are shown
depends on the water hardness level set on the
appliance.
The descaling procedure can also be performed
whenever the user desires a deeper cleaning of the
internal steam circuit.
Before to run the descaling phase, the appliance will
check if some residual water is contained into the
boiler, and a Drain cycle could be performed, if
needed. In this case, you will have to empty the
drawer after the Drain cycle, before continuing with
the Descale Phase.
Please note: to ensure that the water is cold, it is not
possible to perform this activity before 30 minutes have
elapsed from the last cycle (or the last time the product
was powered). During this waiting time, the display will
show the following feedback “WATER IS HOT”.
» PHASE 1/2: DESCALING (70 MIN)
When display will show <ADD 0.25 L OF SOLUTION>,
please pour the descaling solution in the drawer. For
best results in descaling, we recommend filling the
tank with a solution composed of 75 g of the specific
WPRO product and 250 ml of drinking water. WPRO
descaler is the suggested professional product for the
maintenance of the best performance of your steam
function in the oven. For orders and information
contact the after sales service.
Bauknecht will not be held responsible for any
damage caused by the use of other cleaning products
available on the market.
Once the descaling
solution is poured
inside the drawer,
press
to start
the main descaling
process. The
descaling phases
do not need you to
stay in front of the
appliance. After
each phase is
completed, an acoustical feedback will be played and
the display will show instructions to proceed with the
next phase.
Once the descaling phase has been completed, the
boiler will be drained: the descaling solution used
during this phase will be poured into the extractable
drawer.
» PHASE 2/2: RINSING (30 MIN.)
To remove descale residuals from the drawer and
the steam circuit, rinse cycle has to be done. When
display shows <ADD 0.25 L OF WATER> fill the tank
with 0,25 L of drinking water, then press
to start
the rinsing. Do not turn off the oven until all the steps
required by the function have been completed.
Please note: if needed from the system, it could be
requested to emty the drawer and to repeat this
operation.
When Descale procedure is completed, it is suggested
to dry the cavity from potential water residuals. It will
be then possible to use all the steam functions.
Please note: during the Descale cycle, some noise could
potentially be heard since the oven pumps are activated
in order to guarantee the optimal descale efficiency.
Once the maintenance cycle has started, do not remove
the drawer unless requested by the appliance.
Please note: After the boiler gets filled by the descaling
solution and the display shows “DESCALING PHASE 1/2”,
the cycle should not be interrupted and/or the door
opened, otherwise the entire descaling cycle must be
repeated before being able to run any steam function.
1+
= 75 g
+2
250 ml
3
Bekijk gratis de handleiding van Bauknecht BCT11A9FHTSK, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Bauknecht |
| Model | BCT11A9FHTSK |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 13628 MB |
