Arktic 232491 handleiding
Handleiding
Je bekijkt pagina 14 van 156
14
GB
res 10Min.) at the end of this time it switches to next phase.
• If the cycle is temperature cycle for the second phase -
This value is used only if there is a core probe; this is the
maximum duration of the second phase if the temperature
defined in parameter iS2 is not reached.
13. Set point of the storage phase.
Cleaning & maintenance
• ATTENTION! Always disconnect the appliance from the power
supply and cool down before storage, cleaning & maintenance.
• Do not use water jet or steam cleaner for cleaning and do not
push the appliance under the water as the parts will get wet
and electric shock might be resulted.
• If the appliance is not kept in a good state of cleanliness, this
can adversely affect the life of the appliance and result in a
dangerous situation.
• Food residues should be regularly cleaned and removed from
the appliance. If the appliance is not cleaned properly, it will
reduce its lifespan and may result in a dangerous condition
during use.
• Before cleaning chamber perform a defrost cycle.
Cleaning
• Clean the cooled exterior surface with a cloth or sponge slight
-
ly dampened with a mild soap solution.
• For reasons of hygiene, the appliance should be cleaned before
and after use.
• Avoid water contacting the electrical components.
• Never immerse the appliance in water or other liquids.
• Never use aggressive cleaning agents, abrasive sponges, or
cleaning agents containing chlorine. Do not use steel wool,
metallic utensils, or any sharp or pointed objects for cleaning.
Do not use petrol or solvents!
• Clean the door seal with water only.
• Clean needle probe at least one time per day.It is recommend
-
ed to rinse probe with clean water and sanitizing solution.
• Periodically clean the condenser (followed only by qualified
technicians) using suitable tools (see fig. 8 on page 6)
Maintenance
• Check the operation of the appliance regularly to prevent se
-
rious accidents.
• If you see that the appliance is not working properly or that
there is a problem, stop using it, switch it off and contact the
supplier.
• All maintenance, installation and repair work must be carried
out by specialised and authorised technicians, or recommend
-
ed by the manufacturer.
Transportation and Storage
• Before storage, always make sure that the appliance has been
disconnected from the power supply and completely cooled down.
• Empty refrigerating chamber and clean it before storage the appli
-
ance. Store the appliance in a cool, clean and dry place.
• Never place heavy objects on the appliance as this could damage it.
• Do not move the appliance while it is under operation. Disconnect
the appliance from power supply when moving and hold it at the
bottom.
• Special care must be taken when moving or transporting the ma
-
chine due to its heavy weight. With at least 2 persons or using a
cart. Move the machine slowly, carefully, and never incline more
than 45°.
Troubleshooting
If the appliance does not function properly, please check the
below table for the solution. If you are still unable to solve the
problem, please contact the supplier/service provider.
Problem Possible cause Possible solution
The
appliance
is not
working.
Appliance is turn off.
Check plug connection and
if the appliance is turn on.
Plug and/or cord are
damaged.
Contact the supplier.
Fuse blown. Contact the supplier.
No power supply. Check power supply.
The
appliance
turns on,
but the
tempera
-
ture is too
high/too
low.
There is too much ice on
the evaporator.
Start defrost cycle.
Condenser is blocked
with dust.
Contact the supplier.
Doors are not close
properly.
Check if the doors are close
correctly and if the seals are
damaged.
The appliance is located too
close to a heat source or
the air flow to the condens
-
er is being interrupted.
Move the appliance to a
more suitable location
Ambient temperature is
too high.
Increase ventilation or move
the appliance to a more
suitable location.
Unsuitable food products
are being stored inside the
appliance.
Remove food products that
are too hot for storage or are
blocking the fan inside the
appliance.
The appliance is over
-
loaded.
Reduce the amount of
food products stored in the
appliance.
The ap
-
pliance is
unusually
loud.
Loose nut/screw.
Check and tighten all loose
nuts/screws.
The appliance is not
installed on a level, stable
surface / is not properly
leveled.
Check the installation
position and/or adjust feet to
level appliance.
Leaking
water
from
appliance
The drain outlet is blocked. Clear drain outlet.
Movement of water to the
drain is obstructed
Clear bottom of the
chamber.
Water container is
damaged.
Contact the supplier.
The drip tray is overflowing. Empty the drip tray.
Alarms / Error codes
If any alarm will be exist, error code and alarm icon will be
displayed on the control panel; also acoustic alarm will be ac
-
tivated. To turn off acoustic alarm press any button on control
panel. To reset alarm manually, press and hold SETTING button
for 5 seconds. To solve problem chceck table below:
Error Possible cause Possible solution
rPf Chamber probe failure.
Probe connection are loose or not
working, check thermostat connec
-
tion. Compressor output according
to parameters “Con” and “Cof”.
2nf Core probe failure.
Probe connection are loose or
not working, check thermostat
connection.
AH
Alarm of maximum
temperature.
Outputs unchanged (manual reset).
Bekijk gratis de handleiding van Arktic 232491, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Arktic |
| Model | 232491 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 27120 MB |
