Handleiding
Je bekijkt pagina 14 van 22
37V 01/24
operating in Cooling or Heating mode.
In Cooling: after the rst hour the set temperature increases by 1 °C, after the second hour it increases again by
1 °C.
In Heating: after the rst hour the temperature decreases by 1 °C, after the second hour it decreases again by 1
°C.
The temperature is then kept constant for 10 hours, all LEDs on the control panel turn off. The ventilation speed
decreases to minimum to ensure silence during the night hours, and it is not possible to adjust it.
4. UP/DOWN BUTTONS
Press UP/DOWN buttons on the control panel to adjust the temperature (1 °C steps) and set the Timer (each time
the buttons are pressed the adjustment step is 1 hour up to 24 hours.
The temperature can be adjusted from 16°C to 32°C.
On the remote controller, instead, press the - TEMP/HRS + button to increase the temperature, while to set the
Timer, press the Timer button then use the - TEMP/HRS + button to select the desired time.
To deactivate the Timer, set the time to 00.
5. SWING BUTTON
Press this key to turn on or off the horizontal louver swing.
6. FAN SPEED BUTTON
Press this button on the control panel or remote controller to adjust the fan speed in the following circular sequence:
high, medium, low.
The LEDs on the control panel light up according to the selected speed.
The fan speed cannot be adjusted in DRY mode and is xed at low.
7. TIMER BUTTON
Press this button on the control panel or remote controller to set the unit’s On or Off Timer, the adjustment range is
from 1 to 24 hours.
On Timer: When the air conditioner is off, press TIMER to set a time to turn on the unit. Press the UP/DOWN
buttons on the control panel or + - button on the remote controller to set the time.
Off Timer: When the air conditioner is on, press TIMER to set the time to turn off the unit. Press UP/DOWN on
the control panel or + - button on the remote controller to set the time.
To cancel the Timer function, press the UP/DOWN buttons repeatedly, 00 will appear on the display.
When the air conditioner is turned off with the Power button, the Timer function is cancelled.
DISPLAY OF TEMPERATURE °C / °F
Press this button on the remote controller to change the temperature display from °C to F°.
WIFI FUNCTION
To activate or deactivate the Wi function, press and hold the Timer button on the control panel to begin
conguration. The LED on the control panel lights up.
For Wi conguration, refer to the dedicated paragraph.
AUTOMATIC DEFROST FUNCTION
If the ambient temperature is low, frost may form on the evaporator during operation. The unit will automatically
begin defrosting and the POWER LED on the control panel will ash. The defrost sequence is as follows:
• When the unit operates in cooling or dehumidifying mode, the room temperature sensor detects that the
evaporator temperature is below -1°C, then the compressor stops operating for 10 minutes until it reaches the
temperature of 7°C, then the unit continues to operate in cooling mode.
• When the unit operates in heating or dehumidication mode, if the temperature sensor detects that the
evaporator temperature is less than 40°C and if the temperature difference between the evaporator temperature
and the room temperature is less than 19° C, the compressor runs for 20 minutes, the unit starts defrosting for
5 minutes and the POWER LED on the control panel will ash.
OVERLOAD PROTECTION FUNCTION
In the event of a forced power failure, the unit resumes operation after 3 minutes to allow the compressor to restart.
Bekijk gratis de handleiding van Argoclima Twiggy Plus, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Argoclima |
| Model | Twiggy Plus |
| Categorie | Airco |
| Taal | Nederlands |
| Grootte | 2439 MB |
