Aqara Light Switch H2 handleiding
Handleiding
Je bekijkt pagina 2 van 6
Warnings
1. This product is not a toy. Please keep it away from children.
2. This product is designed for indoor use only.
3. Do not use in humid environments or outdoors.
4. Moisture will damage the product. Do not spill water or other liquids
onto the product.
5. Do not place this product near a heat source. Do not place it in an
enclosed area unless there is adequate ventilation.
6. Do not attempt to repair this product by yourself. All repairs should
be performed by an authorized professional.
7. This product is suitable for home monitoring and smart home
integration, The manufacturer is not responsible for any risks or
property losses caused by misuse or failure to follow the product
instructions.
Light Switch H2 US (2 Buttons, 1 Channel)
Installation Method
1. Please make sure that the power at circuit breaker or fuse box is
turned o before wiring!
2．Identify the type of electrical circuit in your home. For the 2 button
and 1 channel switch, we support three types of circuits:
a)single pole
b)3-way (light outside two switches)
c)3-way (light between two switches)
Please follow the instructions below to determine your home's
circuit type and wire it correctly. For 3-way circuit wiring, we
recommend seeking assistance from a professional electrician.
3. Mount the switch unit to the electrical box with the attached screws.
Then mount the frame to the switch unit with screws, and attach the
faceplate cover to the frame.
4. Turn on the power at the circuit breaker and test the switch by
pressing the upper button. If the wired light can be controlled by the
upper button, the switch is functioning correctly.
5. In the Aqara Home app, tap Add Accessory, choose Light Switch H2
US. Scan the Matter QR Code on the paper manual to add the device
to the app. The following Quick Setup section will introduce the
network configuration methods for both Zigbee and Thread
protocols.
Product Introduction
Light Switch H2 US (2 Buttons, 1 Channel)
Aqara Light Switch H2 US is a smart switch based on Thread/Zigbee
wireless communication protocols which can control lights,
automations, and scenes. When used with a hub, it can be controlled
via the app, and has features for scheduling, power monitoring, power
statistics, and other functions. It can also be used with other smart
devices to enable a variety of interconnected control functions.
*This product needs to be used with a device that has Matter Border Router function.
* Use only one switch in a 3-way circuit, the other end needs to be a normal standard
switch. Both the old and new switch circuits need to be rewired according to the
diagram.
EN
Plate Screws
Screws
Frame
Relay Switch
Indicator Light
Indicator Light
Matter Code
Wireless Switch
Wireless Switch
Switching unit
Light Switch H2 US (2 Buttons, 2 Channels)
Plate Screws
Screws
Frame
Relay Switch
Relay Switch
Indicator Light
Indicator Light
Matter Code
Switching unit
Light Switch H2 US (4 Buttons, 3 Channels)
Plate Screws
Screws
Frame
Relay Switch
Relay Switch
Relay Switch
Matter Code
Switching unit
OFF
Single Pole Wiring
3-Way（Light Outside Two Switches）
* Use only one switch in a 3-way circuit, the other end needs to be a normal standard
switch. Both the old and new switch circuits need to be rewired according to the
diagram.
*If the QR code on the paper manual is lost, you can remove the plastic cover frame
and scan the QR code on the mounting bracket of the product.
3-Way（Light Between Two Switches）
NTWL1
G
L
TW
L1
G
N
(
O
pt
)
L
N
AerBefore
L
N
C
T T
C
T T
C
T T
N
L L1
G
TW
N
L
1
TW
G
N
(O
p
t
)
L
AerBefore
L
L
N
N
C
T T
C
T T
L L1 TW
N
N
L
C
T T
G
L
1
TW
G
N
(
Opt
)
L
ON
Light Switch H2 US (2 Buttons, 2 Channels)
Light Switch H2 US (4 Buttons, 3 Channels)
1. Please make sure that the power at circuit breaker or fuse box is
turned o before wiring!
2. For users with Light Switch H2 US (2 Buttons, 2 Channels) or (4
Buttons, 3 Channels), please follow the corresponding wiring
methods according to your product model. It is recommended to
seek assistance from a professional electrician to complete this step.
3. Mount the switch unit to the wall electrical box with the attached
screws. Then mount the frame to the switch unit with screws, and
attach the faceplate cover to the frame.
OFF
L2
L1
L
N
(Opt)
N
L1
L2
L1
G
L2L N
G
2 Buttons, 2 Channels
4 Buttons, 3 Channels
N
(Opt)
L3
L2
L1
L
N
L1
L2
L3
L1
G
L2 L3L N
G
4. Turn on the power at the circuit breaker and test the switch by
pressing the upper button. If the wired light can be controlled by the
upper button, the switch is functioning correctly.
5. In the Aqara Home app, tap Add Accessory, choose Light Switch H2
US. Scan the Matter QR Code on the paper manual to add the device
to the app. The following Quick Setup section will introduce the
network configuration methods for both Zigbee and Thread
protocols.
ON
*If the QR code on the paper manual is lost, you can open the product cover and
scan the QR code on the metal frame of the product.
Quick Setup
1. Double-press any button, then press and hold it for 5 seconds until
the green indicator light starts blinking. This indicates that the
device is in pairing mode.
2. Open the app that supports Matter, scan the Matter code on the
manual or product, or enter the setup code to add the device to the
app.
3. Proceed following the app's instruction.
To use the device with a particular Matter ecosystem (Thread
Mode), a Matter Controller of this ecosystem and a Thread
Border Router are required.
1. Double-press any button, then press and hold it for 5 seconds until
the green indicator light starts blinking. This indicates that the
device is in pairing mode.
2. In the Aqara Home app, tap Add Accessory, choose Light Switch H2
US. Scan the Matter code on the manual or product or enter the
setup code to add the device to the app. Select Thread on the
Switch Protocol page.
3. Proceed by following the app's instruction.
To use the device in Aqara Home (Thread Mode), an Aqara
Hub with border router function (for example, Hub M3) is
required:
1. Double-press any button, then press and hold it for 5 seconds until
the green indicator light starts blinking. This indicates that the
device is in pairing mode.
2. In the Aqara Home app, tap Add Accessory, keep your phone close to
the device, and Light Switch H2 US will appear in the app's discovery
section (at the top le). Tap the icon and select Zigbee on the Switch
Protocol page.
3. Proceed by following the app's instruction.
To use the device in Aqara Home (Zigbee Mode), an Aqara
Zigbee Hub is required:
Regarding Dual Protocol (Thread/Zigbee) Switching
Q: How to switch from Thread protocol to Zigbee protocol?
A:
1.Install the Aqara Home app, and enable Wi-Fi and
Bluetooth.
2.Reset the device to factory settings (press any button 10
times continuously) to enter network setup (the first time you
add the device it will automatically begin pairing), with its
green indicator light flashing quickly.
3.In the Aqara Home app, tap Add Accessory, scan the Matter
code on the manual or product, then select Zigbee on the
Switch Protocol page. Proceed by following the app's
instruction.
Q: How to switch from Zigbee protocol to Thread protocol?
A:
1.Install the Aqara Home app, and enable Wi-Fi and
Bluetooth.
2.Reset the device to factory settings (press any button 10
times continuously), then enter network setup (yellow
indicator light flashes quickly).
3.In the Aqara Home app, tap Add Accessory, keep the phone
close to the device, and the Light Switch H2 US will show in
the app's discovery section (at the top le). Tap the icon and
select Thread in the Switch Protocol page. Proceed by
following the app's instruction.
Indicator Light Description
Indicator light status
Description
Green indicator light quickly flashes 3 times Device powered on
Pairing/Seeking Device
Pairing/Seeking Device (Thread protocol)
Device oline
Green indicator light flashes slowly
Green indicator light flashes quickly
Green indicator light stays on for 1s Pairing successful
Red indicator light stays on
Device voltage is unstable, please
connect to a higher power load
Red indicator light flashes slowly 3 times
Seeking device (Zigbee protocol)Yellow indicator light flashes quickly
Product Specifications
Product Name
Model
WS-K02E WS-K03E WS-K04E
Thread, Zigbee, Bluetooth
119 × 74 × 42mm
Wireless Protocols
Dimensions
Electrical Rating
120 VAC, 60 Hz,
Max 10 A (Resistive Load or Incandescent), µ
Light Switch H2 US × 1, Compliance
Statement × 1, User Manual × 1, Screw Kit × 1,
Wire Nuts Kit × 1, Wiring Sticker Sheet × 1
5 W (No Neutral), Unlimited (With Neutral),
general purpose
Minimum Power
2400-2483.5Mhz
ThreadOperation Frequency
≤ 13 dBm
2400-2483.5Mhz
≤ 13 dBm
0°C ~ 40°C (32°F ~ 104°F)
0 ~ 95% RH, no condensation
Thread Maximum OutputPower
Bluetooth Operation Frequency
Bluetooth Maximum Output Power
Operating Temperature
Operating Humidity
What is in the Box
Button Opreation
Single press
Turn On/O
Double press, then press and hold for 5
seconds within 3 seconds
Reset the Device/Enable Pairing
Reset to factory settings
Configure and define these Wireless
Switch Mode actions under Automation
in Aqara Home (Zigbee Mode)
Press any button 10 times continuously
Single-Press Mode：Singe Press
Multi-function Mode: Single Press,
Double Press, Long Press
Light Switch H2
US (2 Buttons, 1
Channel)
Light Switch H2
US (2 Buttons, 2
Channels)
Light Switch H2
US (4 Buttons, 3
Channels)
Bekijk gratis de handleiding van Aqara Light Switch H2, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Aqara |
| Model | Light Switch H2 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 1446 MB |
