Anthem MDX-16 handleiding

Handleiding

12345678910111213141516171819202122232425262728293031323334353637383940/ 40

Afdrukken

Je bekijkt pagina 33 van 40

33

8. FREQUENTLY ASKED QUESTIONS

HowdoIndtheIPaddressofmyMDX?

We recommend using Anthem’s ARC Genesis software or us-

ing a utility called Fing. See section 2.2 for additional details.

I’m connecting my DVD player to the MDX using a TOS in-

put, but even if the disc is playing, I do not hear any sound.

The MDX digital input only supports a PCM stream. Access

your DVD player setup menu and change the output format

to PCM.

I have a subwoofer connected to the MDX using an RCA

jack, but even if I’m playing music with lots of low-fre-

quency content, the subwoofer does not work.

Enable the subwoofer (the default setting is o). See section

2.4 for additional information.

I’m sending commands to the MDX using the serial port,

but the MDX does not react.

Make sure to congure your controller to 115200/8-N-1. Make

sure to send the terminator “;” at the end of the command. CR/

LF are not required.

I’mconguringapairofspeakersinstereobridgemode

on zones 1 and 2. I have my left speaker on zone 1 and

my right speaker on zone 2. My source’s left channel is

attached to the Analog 1 left input and its right channel

connected to the Analog 2 right input. I only hear sound

fromtheleftchannel.WhatamIdoingwrong?

Inputs and speakers (even bridged speakers) operate inde-

pendently of one another. Attach your source’s left and right

channels to the Analog 1 inputs and set Zone 1’s Input Source

to Analog 1. When in bridge mode, Zone 1 becomes the “mas-

ter,” so source selection, volume change, tone control, are all

done by accessing the Zone 1 panel. All settings in Zone 2 set

before selecting Stereo Bridge mode are no longer relevant.

My CD player analog output level cannot be controlled

and defaults to a very high level (2 Vrms). When playing

music, the MDX seems to be clipping very often. How can

thisbeavoided?

The MDX allows you to change the trim of any source. Select

the Inputs pane and set the trim level between -6 dB to -9 dB

for the source where your CD player is connected.

How does the MDX work when the On Mode switch is set

toAuto?

When the MDX is in standby, it monitors all analog and digital

connectors to check if the unit needs to turn on:

• Analog connectors are monitored for a signal higher than

-60 dBV (1 mVrms).

• Digital connectors are monitored by checking if there

is any bit toggling on the coaxial or Toslink inputs. The

MDX doesn’t check for a specic level to achieve <1/2W in

standby, only activity.

When in operation, the active channels are monitored. When

the level drops below -60 dBV (for either analog or digital in-

puts) for the amount of time programmed in the Auto-O de-

lay, the zone turns o. If all zones are o, the unit will go in

standby.

12345678910111213141516171819202122232425262728293031323334353637383940/ 40

Bekijk gratis de handleiding van Anthem MDX-16, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.

Productinformatie

Gerelateerde producten van Anthem (Niet gecategoriseerd)

Handleiding bekijken

Anthem MDX-8

Niet gecategoriseerd - handleiding

Andere merken in Niet gecategoriseerd