American DJ Scene Setter 48 handleiding
Handleiding
Je bekijkt pagina 32 van 40
1. Will run all programs synchronously.
2. All programs can be controlled by the same SLIDER SPEED, or each programs
speed may be controlled individually. (See Speed Setting ).
3. Press the MODE SELECT BUTTON and select "CHNS SCENES".
4. Press the PARK BUTTON to select MIX CHASE MODE. A yellow LED will
indicate this selection.
5. Brief of Main Functions
4. Brief of Main Functions
1. The Tap Sync button is used to set and synchronize the chase rate (the rate at which
all scenes will sequence) by taping the button several times. The chase rate will synchronize
to the time of the last two taps. The LED above the Step Button will flash at the new chase
rate. The chase rate may be set anytime whether or not a program is running.
2. Tap Sync will override any previous setting of the speed slider control until the slider is
moved again.
3. Use of Tap Sync in setting a standard beat is the same with speed control slider.
Tap Sync Button:
1. Reverse the direction of all the scenes:
Press the ALL REV Button, all the scenes should change their directions.
2. Reverse the chasing direction of all the programs with speed control.
Press the Chase Rev Button.
3. Reverse the chasing direction of all the programs with standard beat:
Press the Beat Rev Button.
4. Revers chasing direction of any program:
Press and hold down the Rec One Button, then press down the Flash Button
corresponding to your desired program and release together.
Reverse the direction of the scene
1. The amount of time it will take for the dimmer to go from zero output to maximum
output, a nd vice verse.
2. Fade time is adjusted through the Fade Time Slider, which varies from instant to
10 minutes.
Fade Time
Master Slider control provides proportional level control over all channels and scenes
with the exception of the Flash Buttons. For example:
Whenever the Master slider control is at minimum all stage outputs will be at zero except
for any resulting from a Flash Button or FULL ON Button.
If the Master is at 50%, all outputs will be at only 50% of the setting of current channel
or scenes except for any resulting from a Flash Button or FULL ON Button.
If the Master is at full all outputs will follow the unit setting.
Master A always controls outputs of channels. Master B controls the program or a scene
except in Double Preset Mode.
Master Slider
1. The 3-Digit Segment Display is used to display intensity percentage or absolute
DMX value.
2. To change between percentage and absolute value:
Press and hold the Shift Button. While holding down the Shift button press the
% or 0-255 Button to switch between percentage and absolute values.
3. If the Segment Display reads, for example, "076", it means a percentage value 76%.
If the Segment Display reads "076.", it means the DMX value 76.
Dimmer Display
Mix Mode
Blind and Home
1. Blind function takes channels temporally out from a chase, when the chase is running,
and gives you manual control over the channel.
2. Press and hold the Blind Button and tap the relative Flash Button you want to temporarily
take out of the chase.
3. To return to normal chase again press and hold the Home Button and push the Flash
Button you want to return to normal chase.
1. All programs will run in sequential order starting in the order of program number.
2. The Segment Display will read the running program number.
3. All programs will be controlled by the same Speed Slider .
4. Press the MODE SELECT BUTTON and select " CHNS SCENES".
5. Press the PARK BUTTON to select SINGLE CHASE MODE. A red LED
will indicate this selection.
Single Mode
28
29
Bekijk gratis de handleiding van American DJ Scene Setter 48, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | American DJ |
| Model | Scene Setter 48 |
| Categorie | Verlichting |
| Taal | Nederlands |
| Grootte | 3092 MB |
