American Audio RollerTron handleiding

Niet gecategoriseerd

American Audio

8 pagina's

PDF beschikbaar

Handleiding

RollerTron™ Lamp Replacement

©American DJ® - www.americandj.com - RollerTron™ Instruction Manual Page 11 ©American DJ® - www.americandj.com - RollerTron™ Instruction Manual Page 12

Caution: Always replace with the exact same type lamp, unless oth-

erwise specified by an authorized American DJ® service technician.

Replacing with anything other than the specified part can damage

your unit and will void your manufactures warranty.

Warning: If you continue to blow lamps or the breaker, STOP using

the unit. Contact customer support for further instructions, you may

have to return the unit for servicing. Continuing to use the unit may

cause serious damage.

Lamp Replacement: Caution! Never attempt to change the lamp

while the fixture is plugged in. Always disconnect the main power

and allow the unit ample time to cool before attempting to replace the

lamp. Lamp replacement has been made simple by incorporating the

use of a flip-up front cover that is retained by thumb screws.

1. Be sure to follow the proper handling procedures that deal with

halogen lamps.

2. Remove the thumb screw on the rear of the unit that holds the

lamp socket assembly cover in place.

3. After removing the thumb screw, slide out the cove from the rear

of the unit to expose the lamp socket assembly.

4. Carefully remove the old lamp and discard it in the trash.

5. Replace the lamp with an exact match and reassemble in reverse

order.

This unit is equipped with a built-in safety breaker. This breaker is

designed to close the power circuit in the event of an internal short

or power surge. This will reduce the risk of electrical shock or re and

protect the circuitry. To reset the breaker, push the breaker button in

until you hear it “pop” back in to place. If the breaker continues to

pop, stop using the unit and contact our customer support team, the

unit may need to be returned for service.

RollerTron™ Set Up

Figure 3

1 Ground

XLR Male Socket

XLR Pin Conguration

3 Hot

2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

Special Note: Line Termination.

When longer runs of cable are

used, you may need to use a terminator on the last unit to avoid erratic

behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is con-

nected between pins 2 and 3 of a male XLR connector (DATA + and

DATA -). This unit is inserted in the female XLR connector of the last

unit in your daisy chain to terminate the line. Using a cable terminator

(ADJ part number Z-DMX/T) will decrease the possibilities of erratic

behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 4

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin XLR

connectors for DATA transmission in place of 3-pin. 5-pin XLR xtures

may be implemented in a 3-pin XLR DMX line. When inserting stan-

dard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be

used, these adaptors are readily available at most electric stores. The

chart below details a proper cable conversion.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Pin 1

Pin 5 - Do Not Use

Pin 4 - Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion

RollerTron™ Breaker Reset

Bekijk gratis de handleiding van American Audio RollerTron, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.