Alpina B32 handleiding

Handleiding

1234567891011121314151617181920212223242526272829303132333435363738394041424344454647/ 47

Afdrukken

Je bekijkt pagina 25 van 47

EN - 3

• Check that there is nobody within 15

metres of the machine’s range of action

or within 30 metres for heavier cutting;

• Where possible, avoid working on

wet, slippery ground or in any case on

uneven or steep ground that does not

guarantee stability for the operator;

• Pay particular attention to uneven

ground (humps, hollows), slopes, hidden

hazards, or the presence of obstacles

that could compromise visibility.

• Be very careful near ravines,

ditches or embankments.

• Always work across the face of the slope

and never up and down it, being very careful

when changing direction, making sure the

cutting means is always downstream.

• Look out for trac when using

the machine near the road.

Behaviour

• When working, the machine must always

be rmly held in both hands, keeping the

power unit on the right of the body and the

cutting group below the line of the belt.

• Always use caution and take on a

rm and well-balanced position.

• Never run, always walk.

• Always keep the machine connected

to the harness when working.

• Always keep hands and feet away

from the cutting means, when starting

and when using the machine.

• Warning: the cutting means continues

to rotate a few seconds even after

it has been disengaged or the

engine has been switched o.

• Be careful of ying debris coming

from the cutting means.

• Take care not to hit the cutting means

against foreign objects/obstacles. Kickback

can occur if the cutting means contacts an

obstacle/object. This contact can cause

a rapid backward motion, pushing the

cutting means up and towards the operator.

Kickback can cause the operator to lose

control of the machine, leading to serious

consequences. Kickback can be avoided

by taking proper precautions as given below:

– Hold the machine rmly in both hands

and position your body and arms so that

you can resist the force of a kickback;

– Do not overreach and do not cut

above the line of the belt;

– Only use replacement cutting means

specied by the manufacturer;

– Follow the manufacturer’s maintenance

instructions for the cutting means.

• Beware of injuries caused by devices

used to cut the line length.

• Do not touch the engine parts, which

heat up during use. Burns hazard.

• To avoid the risk of re, do not leave the

machine with the engine hot on leaves,

dry grass or other ammable material.

•

If something breaks or an accident

occurs during work, turn o the engine

immediately and move the machine away

to prevent further damage; if an accident

occurs with injuries or third parties are

injured, carry out the rst aid measures

most suitable for the situation immediately

and contact the medical authorities for any

necessary health care. Carefully remove

any debris which could cause damage or

injury to persons or animals if ignored.

•

The noise and vibration levels shown

in these instructions are the maximum

levels for use of the machine. The use of an

unbalanced cutting means, excessive speed

of movement, the absence of maintenance

have a signicant inuence on noise

emissions and vibrations. Consequently,

it is necessary to take preventive steps to

eliminate possible damage due to high levels

of noise and stress from vibration. Maintain

the machine well, wear ear protection

devices, and take breaks while working.

•

Prolonged exposure to vibrations can

cause injuries and neurovascular disorders

(also called “Raynaud’s syndrome” or

“white hand”), especially to people suering

from circulation disorders. The symptoms

can regard the hands, wrists and ngers

and are shown through loss of sensitivity,

torpor, itching, pain and discolouring of

or structural changes to the skin. These

eects can be worsened by low ambient

temperatures and/or by gripping the

handgrips excessively tightly. If the symptoms

occur, the length of time the machine is used

must be reduced and a doctor consulted.

Use limitations

• Do not use the machine if you are unable

to hold it with both hands or keep it

steady on your legs while working.

• Never use the machine with damaged,

missing or not correctly positioned guards.

• Do not alter the engine adjustments, nor

over-run it. If the engine is forced to work

with an excessive number of rotations,

the risk of personal injury increases.

• Do not strain the machine too much and

do not use a small machine for heavy-

duty work. If you use the right machine,

you will reduce the risk of hazards and

improve the quality of your work.

1234567891011121314151617181920212223242526272829303132333435363738394041424344454647/ 47

Bekijk gratis de handleiding van Alpina B32, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.

Productinformatie

Andere merken in Niet gecategoriseerd