Handleiding
Je bekijkt pagina 6 van 16
6
INSTRUCTIONS FOR THE INSTALLER
Important notice:
The operations indicated below must be followed by authorised personnel exclusively, in
conformity with the regulations in force.
The manufacturing firm refuses all responsibility for damages to people, animals or things,
resulting from the failure to comply with such provisions.
This appliance shall be installed only by authorised persons and in accordance with the
manufacturer’s installation instructions, local gas fitting regulations, municipal building codes,
electrical wiring regulations, and any other statutory regulations. For Australia and New Zealand
this appliance must be installed by an authorised person in compliance with AS/NZS 5601.1 Gas
installations part 1: general installations, and AS/NZS 5601.2 Gas installations part 2: LP GAS
installations in caravans and boats for nonpropulsive purposes. For outside of Australia/New
Zealand refer to the relevant installation code for gas appliances in your country.
INSTALLATION
The installation kit contains the following:
– 1 natural gas regulator
– 1 elbow
– 1 manifold
– 2 fibre sealing washers
– 4 brackets for assembly
– 4 bracket screws
– 1 pack of cooktop to benchtop seals
– 1 duplicate rating label
For conversion to LPG
– 1 Universal LPG sticker
– 6 or 4 injectors.
Additional accessory for cooking with vessels
diameter 120mm or below
– 1 mini trivet
Installing the top
The appliance is designed to be embedded into heat-
resistant benchtop capable of withstanding 85°C.
Adjacent walls, cupboards and protection for
combustible materials.
Ensure that the appliance is installed in
accordance with clauses 6.2.5 and 6.10.1.1 of AS/
NZS 5601.1, or clauses 6.9.1 and 6.9.5 of
AS/NZS 5601.2 with regard to clearances
to combustible surfaces and materials, and
clearances to rangehoods and exhaust fans.
Clearance of 200mm from the periphery of burners
to vertical combustible surfaces is required.
Clearances to combustible surfaces may be
reduced only if combustible surfaces are protected
in accordance with clause 6.10.1.2 of AS/NZS
5601.1, or clause 6.9.2 of AS/NZS 5601.2.
INSTRUCTIONS FOR THE USER
CLEANING
Before any operation, disconnect the appliance from
the electrical supply.
Don’t use a steam cleaner for the cleaning the hob.
It is advisable to clean the appliance when it is cold.
Enamelled parts
The enamelled parts must be washed with a sponge and
soapy water or with a light detergent.
Do not use abrasive or corrosive products.
Do not leave substances, such as lemon or tomato juice,
salt water, vinegar, coffee and milk on the enamelled
surfaces for a long time.
Burners and pan supports
These parts can be removed to make cleaning easier.
The burners must be washed with a sponge and soapy
water or with a light detergent, wiped well and placed in
position perfectly. Make sure that the burner flame ports
are not clogged. Check that the probe of the
thermocouple and the spark plug are always cleaned,
to ensure optimum operation.
Gas taps
The possible lubrication of the taps must be carried out by
authorised personnel, exclusively.
In case of malfunctions of the gas taps call customer
service
Bekijk gratis de handleiding van AEG HGC6366BB, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | AEG |
| Model | HGC6366BB |
| Categorie | Fornuis |
| Taal | Nederlands |
| Grootte | 1636 MB |
