AEG F75BV70APM handleiding
Handleiding
Je bekijkt pagina 10 van 48
Regardless of the type of detergent used, set
the right water softener level to ensure good
washing results and to keep the salt indicator
active.
Multi-tabs containing salt are not effective
enough to soften hard water.
Water hardness
German de‐
grees (°dH)
French de‐
grees (°fH)
mmol/l mg/l (ppm) Clarke de‐
grees
Water softener
level
47 - 50 84 - 90 8.4 - 9.0 835 - 904 58 - 63 10
43 - 46 76 - 83 7.6 - 8.3 755 - 834 53 - 57 9
37 - 42 65 - 75 6.5 - 7.5 645 - 754 46 - 52 8
29 - 36 51 - 64 5.1 - 6.4 505 - 644 36 - 45 7
23 - 28 40 - 50 4.0 - 5.0 395 - 504 28 - 35 6
19 - 22 33 - 39 3.3 - 3.9 325 - 394 23 - 27
5
1)
15 - 18 26 - 32 2.6 - 3.2 255 - 324 18 - 22 4
11 - 14 19 - 25 1.9 - 2.5 185 - 254 13 - 17 3
4 - 10 7 - 18 0.7 - 1.8 70 - 184 5 - 12 2
<4 <7 <0.7 <70 < 5
1
2)
1)
Factory setting.
2)
Do not use salt at this level.
The water softener undergoes an automatic
regeneration process.
1)
How to set the water softener level
Make sure the appliance is un user mode.
1. Press .
• The indicators , , and
are off.
• The indicator still flashes.
• The display shows the current setting:
e.g.
= level 5.
2. Press repeatedly to change the
setting.
1)
For the correct water softener operation, the resin of the softener device needs to be regenerated regularly. This
process is automatic and is a part of the normal dishwasher operation. It occurs when the prescribed amount of
water has been used since the previous regeneration process. The amount of water depends on the water softener
level: level 1 - 250 l, level 2 - 100 l, level 3 - 62 l, level 4 - 47 l, level 5 - 25 l, level 6 - 17 l, level 7 - 10 l, level 8 - 5 l,
level 9 - 3 l, level 10 - 3 l. A regeneration process is initiated between the final rinse and the programme end. In
case of the high water softener setting, it may occur also in the middle of the programme, before the rinse (twice
during a programme). Regeneration initiation has no impact on the cycle duration, unless it occurs in the middle of
a programme or at the end of a programme with a short drying phase. In such cases, the regeneration prolongs the
total duration of a programme by 5 minutes. Subsequently, the rinsing of the water softener that lasts 5 minutes
may begin in the same cycle or at the beginning of the next programme. This activity increases the total water
consumption of a programme by additional 4 l and the total energy consumption of a programme by additional 2
Wh. The rinsing of the softener ends with a complete drain. Each performed softener rinse (possible more than one
in the same cycle) may prolong the programme duration by another 5 minutes when it occurs at any point at the
beginning or in the middle of a programme. All the consumption values mentioned in this section are determined in
line with the currently applicable standard in laboratory conditions with water hardness 2.5mmol/L (water softener:
level 3) according to the regulation: the Commission Regulation (EU) 2019/2022. Water temperature, water
pressure and variations of the mains supply can change the values.
10 ENGLISH
Bekijk gratis de handleiding van AEG F75BV70APM, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | AEG |
| Model | F75BV70APM |
| Categorie | Vaatwasser |
| Taal | Nederlands |
| Grootte | 4477 MB |
