Advance Spectrum 18D handleiding

Stofzuiger

Advance

36 pagina's

PDF beschikbaar

Handleiding

GREEN RED CONDITION FUNCTION

ON OFF

Normal operation In normal operation, the green light is constantly illuminated.

OFF ON -

BLINKING

Brush position too low

(heavy loading)

If the condition 2, red light blinking, continues for 10 seconds or more, the control

module will cut out the power supply to the brush motor.

. The red light will still be illuminated until you turn off the switch or unplug the cord.

OFF ON Brush stalled

. The red light will be constantly illuminated and the control module will instantly cut

the power supply to the brush motor, if the brush was stalled accidentally.

. The red light will still be illuminated until you turn off the switch or unplug the cord.

OPERATING THE VACUUM CLEANER

1. Release the power cord from the cord hooks (2) at the backside of

the vacuum cleaner. Turn the lower hook so that the cord is released.

Unwind the whole power cord .

2. Adjust the height of the handle, by pushing at the handle lock button (4)

and then pull or push at handle to comfortable height.

3. Add the cord to the hook and the anti strain clip of the handle in order

to make an anti strain function. Then plug-in the power cord into a

electrical outlet.

4. Turn the Main Power Switch (17) ON. “l” is ON and “O” is OFF. Now

the vacuum motor will start.

5. Step on the Pedal (11) and then tilt the cleaner backwards. Now the brush

motor will start (Dual-versions only). Dual-versions, the green light (7)

at the brush housing (9) will come on to indicate that the brush motor is

running. On single motor versions, the brush is always turning when on.

6. Turn the Height Adjustment Knob (10) to adjust the height that the

brush will operate in - depending on the material at the surface to

be vacuumed. For carpets with short textiles the brush should in the

lower position. Turn the knob to the left (when you are placed in front

of the machine) to lower the brush. For carpets with longer textiles the

brush should in a higher position. Turn the knob to the right (when you

are placed in front of the machine) to set the brush at a higher level. If

the red light comes on, slowly turn the knob in the opposite direction

until the light goes off (Dual-version only).

If the red light (8) stays on continuously, there may be debris wrapped

around the brush, during operation. On double motor units, this can

cause the overload protector for the brush motor to trip. If this occurs,

turn the Main Switch (17) OFF and unplug the power cord. Remove any

debris from the brush and plug in the power cord, turn the Main Switch

(17) back ON. This will automatically reset the overload protector. If the

overload protector trips repeatedly contact your dealer for service. For

more information of the light indicators on the Dual-versions - see the

table below.

NOTE! Always disconnect the power cord before performing any

machine maintenance.

Whenever (15) “Restricted Airﬂ ow Light” indicator comes on, check the

following: Is the bag full and needs to be changed or is the tube, hose or

nozzle blocked.

For details of dust bag replacement see separate instruction in this

manual. If the light comes on before the bag is full, the inside of the bag

may be coated with very ﬁ ne dust (change the bag), or debris may be

built up somewhere between the brush and the bag.

IMPORTANT !

Foot pedal must be used to

release base to

operating/non operation

position. Failure to do so

could result in damage to the

release mechanism.

LowerLower

HigherHigher

On - OffOn - Off

LIGHT INDICATION AND FUNCTION FOR THE BRUSH MOTOR (DUAL - Double Motor Units only!)

Release Release

basebase

Instruction for use Advance Spectrum 12 15 18 - 823 0102 020 E.indd 9Instruction for use Advance Spectrum 12 15 18 - 823 0102 020 E.indd 9 4/12/2011 2:25:29 PM4/12/2011 2:25:29 PM

Bekijk gratis de handleiding van Advance Spectrum 18D, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.