Advance SC4000 handleiding

Boenmachine

Advance

146 pagina's

PDF beschikbaar

Handleiding

A - 16 Advance SC4000 - 56091272 9/2022

INSTRUCTIONS FOR USEA - ENGLISH

LEAD-ACID BATTERIES - CONTINUED

CAUTION!

Electrical components in this machine can be severely damaged if the batteries are not installed and connected properly.

Batteries should be installed by Nilsk or by a qualied electrician.

1 Remove the batteries from their shipping crate and carefully inspect them for cracks or other damage. If damage is evident, contact the

carrier that delivered them or the battery manufacturer to le a damage claim.

2 Turn the Power Switch (H) OFF and remove the Magnetic SmartKey (39).

3 Rotate the Battery Compartment Latch (20) to unlock then tip the seat forward (the gas spring holds the seat open).

4 For additional access the recovery tank can be removed from the machine. NOTE: Disconnect the recovery hose, vacuum motor wiring and

warning beacon wiring then lift the tank straight up and off the machine, using two people or an overhead hoist.

5 Your machine comes from the factory with enough battery cables to install three 12 volt batteries. Using at least (2) people and an

appropriate lifting strap, carefully lift the batteries into the battery compartment and arrange them exactly as shown in FIGURE 2-1. Secure

the batteries as close to the rear and right side of the machine as possible. Use battery spacer to keep batteries from moving. If installing a

mono-block battery use an overhead hoist.

6 Install the battery cables as shown. Position the cables so the battery caps can be easily removed for battery service.

IMPORTANT!: The protective caps supplied with the batteries need to be left on or re-used to completely cover the portion of the

battery terminals that are not being protected by the battery cable terminal cover boots supplied with the battery cables. This also

applies to the in-line fuse holder boot.

7 Carefully tighten the nut in each battery terminal until the terminal will not turn. Do not over-tighten the terminals, or they will be very difcult

to remove for future service.

8 Coat the terminals with spray-on battery terminal coating (available at most auto parts stores).

9 Put one of the black rubber boots over each of the terminals and connect the Machine Battery Connector (19).

10 Make sure the fuse holder boot is covering the fuse holder, the cable end of the Machine Battery Connector (19), and as much of the battery

terminal as possible. Leave the protective caps supplied with the batteries in place or re-use to cover the terminal areas not protected by the

terminal cover boots.

When changing batteries or the charger, please contact your local authorized service center for correct battery, charger and machine

settings to prevent battery damage.

FIGURE 2-1

-NOTES-

ADHESIVE LINER TO BE BACKSPLIT VERT ICALLY

ALL DIMENSIONS ARE CONTROLL ED BY PRODUCTIO N ARTWORK

NON PRINTI NG MAGENTA INDICATES CUT OUT

COLOR: 56E00158-56975034 (BLACK)

COLOR: 56E00158-56975004 (WHITE)

1) MATERIAL: 56E0500 2-03 OR ORACAL 1640.

5 FULL SCALE PRODUCTION ARTWORK

2 3

6.5 ±0.03

3.50 ±0.0 3

4 X R 0.25 ±0.03

REV

DWG NO

TITLE

SHEETS: 1 OF 1

SCALE: 1.000

FUO:

NOTES UNLESS

OTHERWISE SPECIFIED

1. ALL DIMENSIONS IN INCH, [ ] IN MM.

2. DO NOT SCALE DRAWING.

3. ALL DIMENSIONS APPLY AFTER

PLATING AND HEAT TREATING, BUT

BEFORE PAINT ING.

4. REMOVE ALL BURRS AND

SHARP EDGES.

5. SEE 56E00713 FOR TORQUE INFO.

6. APPEARANCE AND FINSH SHALL

COMPLY WITH NILFISK OPERATIONAL

PROCEEDURE 1-720050.

7. WEL D SYMBOLS PER AWS A2.4.

DRAWING STATUS: RELEASED

ASSY:

SIZE

CC: NO

NILFISK INC.

BROOKLYN PARK, MN 55445

Compliance with: NACS 2020

PRJ ENG

18-OCT-2021DRAWN

CANVAS

MATERIAL: SEE NOTES

FINISH: SEE NOTES

56120182

56120E 12-1

SC4000

MLB

DECAL-BATTERY

3D Model: MODEL NAME

Drawing: SAMPLE-DECAL

SHEET

DWG NO

REVISIONS

APPDDFTMDATEECOREV

CPGMLB18-OCT-2021A-15247

RELEASE

56120182

CONFIDENTIAL

THIS DRAWING AND T HE DESIGN REPRESENT ED HEREON IS THE PROPERTY OF NILFIS K INC.,

BROOKLYN PARK, MINNESOTA AND IT HAS BEEN ISSUED WITH THE UNDERSTANDING THAT IT WILL NOT BE REPRO-

DUCED NOR COPIED NOR USED FOR ANY PURPOSE OTHER THAN FOR WHICH IT WAS IS SUED AND RECIPIE NT

AGREES TO RETURN IT UPON REQUEST.

CPG

CPGMLB15-NOV-2021A-15452

UPDATE: ARTWORK

Bekijk gratis de handleiding van Advance SC4000, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.