Adler AD 7077 handleiding
Handleiding
Je bekijkt pagina 12 van 184
12
3. Spraying roller
4. Full dirty water tank container icon
5. Empty clean water tank container icon
6. Self-cleaning mode
7. Battery status
8. High-efficiency mode
Before first use:
1. Remove and dispose of all packing materials and films.
2. Using a damp cloth, wipe the device. Make sure not to get the housing and control panel of the device wet.
3. Fill the dirty and clean water containers rinse the inside of both containers and pour out the water.
Installation:
1. Take the aluminum pipe (A5) and insert it into the hole located at the top of the housing (A11). The tube will pop
into place. See illustration 1 page 3.
2. Press the button located on the clean water container (A12) and pull it towards you to remove the container.
3. There is a silicone plug on the container. It should be removed. Fill the clean water container with tap water. NOTE.
DO NOT USE SCENTED WATER. You can use non-foaming lining liquid in a ratio of 1 part liquid to 9 parts water.
4. Plug the container into the device. Remember to close the silicone plug. See figures 3-7 page 4.
5. Plug the dirty water container into the unit. See figures 8-9 page 4.
6. Plug the roller into the unit. See figures 10-11 page 5.
7. Replace the roller cover by first hooking the front side and then pushing the handle part down so that it snaps into
place. See figures 12-13 page 5.
8. Connect the charger to the charging station (13).
9. Plug the charger into a power outlet.
10. Place the device on the charging station. The device will inform you that it has started charging by lighting up the
screen and giving you a voice message.
Changing the language:
To change the language from the one currently used by the device, press and hold the roller spray button (A3) for 10
seconds and the language will change.
Using the device:
1. After correct installation. Remove the device from the charging station.
2. Make sure that the dirty water container is clean and properly assembled and that the filter is definitely installed in
the container.
3. Make sure the device has a full clean water container.
4. Make sure you hold the vacuum cleaner securely.
5. Turn on the device using the on/off switch (1).
6. The device will start working.
7. Move the device from and to you.
8. You can turn off the roller soaking with the roller spray button (3).
9. You can switch between economy mode and high efficiency mode with the mode change button (2)
10. The device can be tilted up to an angle of 135 . Below this angle, the water in the dirty water container may
indicate a false fill level. If this happens, the device will inform you that the dirty water container is full and will turn
off. In this case, either empty the dirty water container if it is really full or turn on the device again paying attention to
the angle.
11. When it is finished, put the device on the charging station and turn on the automatic cleaning mode using the self-
cleaning button (4). NOTE: if the battery level does not allow you to immediately activate the self-cleaning mode, the
device will schedule self-cleaning and start when the battery is sufficiently charged.
11. When finished, pour out the water from the clean and dirty water container. See the maintenance section of the
manual.
Icons on the display:
If the Full dirty water container icon (B4) appears on the display. Empty the container and rinse it out before returning
to operation.
Bekijk gratis de handleiding van Adler AD 7077, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Adler |
| Model | AD 7077 |
| Categorie | Stofzuiger |
| Taal | Nederlands |
| Grootte | 25215 MB |
