Adler AD 7068 handleiding
Handleiding
Je bekijkt pagina 6 van 128
6
1. Handle
2. Cord holder
3. Metal tube
4. Power switch
5. Power cord
6. Water tank filler
7. Steam head joint
Parts of the machine(Graphic B page 2):
A. Main body
B. Handle
C. Steam head
D. Micro fiber pad
E. Carpet cleaning pad
F. Measure
Before first use:
1. Remove any packing material
2. Wipe all components with a damp soft cloth.
3. Check the condition of the power cord.
Prepare the device for operation:
1. Slide the handle (1) into the main body (A). (Graphic C page 3)
2. There is a bearing in the metal tube (3). It fits into the hole in the main body.
3. When installed correctly, the bearing will fall into the hole in the main body.
4. Connect the steam head (C) to the joint (7) as shown in illustration E page 3.
5. To remove the metal tube, press down on the bearing and pull upward as shown in page 3 illustration C.
6. Attach a microfiber pad to the steam head (C). To remove the pad, pull it firmly.
7. To refresh carpets, apply the carpet cleaning pad (E) should be applied to the previously attached microfiber pad as shown in
illustration D page 3.
8. Fill the device with water. To do this, remove the plug located on the back of the device, pour in tap water using the included
measuring cup. NO MORE THAN 350 ml. Put the plug back in. As shown in illustration F page 3.
Using the device:
1. Put on either a microfiber pad or a carpet cleaning pad, respectively.
2. After preparing the device for use. Plug the device into a power outlet.
3. Switch the switch to the on position.
4. The device will light up red until it heats up. This takes approximately 25 seconds, depending on the temperature of the room and
water, it may be shorter or longer.
5. As the light changes to green the device is ready for use.
6. Move the device slowly and steadily back and forth for best results.
7. Check the amount of water on the main body regularly.
8. When you have finished working, turn off the device and let it cool down.
9. Remove the microfiber pad.
10. Wash and dry the pads after each use to ensure hygienic cleanliness.
11. Pour out the remaining water from the tank.
Decalcification:
Water container:
Depending on the hardness of the water in your home, the appliance should be descaled the water container. To do this, add 2
tablespoons of white vinegar to the full water container and shake the appliance to distribute the solution throughout the water
container. Set the device aside for several hours and empty the water container. Then rinse the entire container with clean water
and leave the device to dry with the water container open.
Steam generating system:
If you notice a drop in steam generation or no steam generation you need to remove the scale from the steam generation system
for this purpose:
1. In a measuring cup, create a solution consisting of 1/3 white vinegar and 2/3 s tap water.
2. Pour the solution into the water container and close the water container.
3. Put the device in a place resistant to acid, temperature, water. E.g.: sink, shower tray, bathtub. A microfiber pad is not needed to
perform descaling.
4. Connect the device to electricity.
5. Turn on the device. The device will start producing steam.
6. Wait until the container empties.
7. If the device still does not produce the previous amount of steam repeat the operation until the desired effect is achieved.
Bekijk gratis de handleiding van Adler AD 7068, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Adler |
| Model | AD 7068 |
| Categorie | Stoomreiniger |
| Taal | Nederlands |
| Grootte | 13671 MB |