Adj Vizi Spot 5R handleiding

Niet gecategoriseerd

Adj

28 pagina's

PDF beschikbaar

Handleiding

American DJ® - www.americandj.com - Vizi Spot 5R Instruction Manual Page 39 American DJ® - www.americandj.com - Vizi Spot 5R Instruction Manual Page 40

Vizi Spot 5R Editing Program

13. Repeat steps 3-12 to edit other scenes, you can edit and

save 48 scenes maximum.

14. Press MODE/ESC to exit, now you have edited and saved

scenes using the control board. The number of steps can be

dened under “Step” and the scenes can be called up under

“Run”. To run the scenes see page 36.

Editing procedure 2: Using an external controller.

1. Access the main menu.

2. Tap the UP button until “EDIT” is displayed. Press ENTER.

3. The display will show “SC01”, this stands for the scene

number to be edited. For example: If “SC01” is displayed, you

will be editing scene 1.

4. Change the scene number by pressing the UP button.

5. Press ENTER, the display will show “C-01”, the “1” stands for

the channel number 1.

6. Press the UP button until “CEDT” is displayed, press ENTER.

7. The display will show “OFF”, press the UP button so that “ON”

is displayed, press ENTER.

8. The display shows “SC02”. You have successfully down-

loaded the rst scene.

9. Adjust the Step-time. needed by pressing the UP button.

10. Call up the second scene in your controller now.

11. Repeat steps 3-6 until all desired scenes are downloaded.

12. Press MODE/ESC to exit. The number of steps can be

dened under “Step” and the scenes can be called up under

“Run”.

Vizi Spot 5R Error Codes

When power is applied, the unit will automatically enter a

“reset/test” mode. This mode brings all the internal motors to a

home position. If there is an internal problem with one or more

of the motors an error code will ash in the display in the form

of “XXer”, “XX” will represent a function number. For example,

when the display shows “03Er,” it means there is some type of

error with the channel 3 motor. If there are multiple errors during

the start-up process they will all ash in the display. For exam-

ple: if the xtures has errors on channel 1 and channel 3 all at

the same time, you will see the error message ash “01Er”, and

“03Er repeated 5 times.

If an error does occur during the initial start-up procedure the

xture will self-generate a second reset signal and try to realign

all the motors and correct the errors, if the errors persist after a

second attempt a third attempt will be made.

If after a third attempt all the errors have not been corrected the

xture will make the following determinations:

1) 3 or more errors - The xture cannot function properly with

three or more errors therefore the xture will place itself in a

stand-by mode until subsequent repairs can be made.

2) Less than 3 errors - If the xture has less than 3 errors, there-

fore most other functions will work properly. The xture will

attempt to operate normally until the errors can be corrected by

a technician. The errors in question will remain ashing in the

display as a reminder of internal errors.

01Er – PAN movement error:

This message will appear after a xture reset, if the pan-yoke’s

magnetic-indexing circuit malfunctions (sensor failed or magnet

is missing) or there is a stepper motor failure (defective motor

or a defective motor IC drive on the main PCB).

03Er – TILT movement error:

This message will appear after a xture reset, if the tilt mag-

netic-indexing circuit malfunctions (sensor failed or magnet is

Bekijk gratis de handleiding van Adj Vizi Spot 5R, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.