Adj Vizi Roller Beam 2R handleiding
Handleiding
Je bekijkt pagina 10 van 30
ADJ Products, LLC - www.adj.com - Vizi Roller Beam 2R Instruction Manual Page 19
Vizi Roller Beam 2R System Menu
button to exit.
INFORMATION
Time Information (Time information is always represented in
hours)
Current Time - This will allow you to check units current running
time.
1. Press the MODE/ESC button to access the main menu. Press
the UP or DOWN buttons so that “Information” is highlighted, then
press ENTER.
2. Press the UP or DOWN buttons until “Time Information” is dis-
played, press ENTER.
3. Press UP or DOWN buttons, until “Current Time” is displayed,
and press ENTER.
4. “XXXX” will now be displayed. “XXXX” represents the current run-
ning time.
5. Press ENTER or press MODE/ESC to exit.
Total Running Time - This will allow you to check units total running
time.
1. Press the MODE/ESC button to access the main menu. Press
the UP or DOWN buttons so that “Information” is highlighted, then
press ENTER.
2. Press the UP or DOWN buttons until “Time Information” is dis-
played, press ENTER.
3. Press UP or DOWN buttons, until “Total Run Time” is displayed,
and press ENTER.
4. “XXXX” will now be displayed. “XXXX” represents the total run-
ning time.
5. Press ENTER or press MODE/ESC to exit.
Last Run Time - This will allow you to check the last running time of
the lamp.
1. Press the MODE/ESC button to access the main menu. Press
ADJ Products, LLC - www.adj.com - Vizi Roller Beam 2R Instruction Manual Page 18
a Master-Slave conguration.
1. Access the main menu, and press the UP or DOWN buttons so
that “Function” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Slave Mode” is displayed,
and press ENTER.
3. Either Slave 1, Slave 2, or Slave 3 will be displayed. Press ENTER
to select either of the three, or press MODE/ESC button to exit.
Auto Program - This function allows the internal programs to run in
either stand-alone or master/slave mode. In “Master” mode the x-
ture will send DMX data to other xtures connect via the DMX chain.
In “Alone” mode the xture will operate as a single xture. The pro-
gram for this mode is selected in the “Select program” section of
the control menu. You can set the number of steps under “Edit pro-
gram”. You can edit the individual scenes under “Edit scenes”. With
this function, you can run the individual scenes either automatically,
i.e. with the adjusted Step-Time.
1. Access the main menu, and press the UP or DOWN buttons so
that “Function” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Auto Program” is displayed,
and press ENTER.
3. Either “Master” or “Alone” will be displayed.
4. Press ENTER to to make your selection, or press MODE/ESC
button to exit.
Sound Control - With this function, the internal program will run in
sound active mode.
1. Access the main menu, and press the UP or DOWN buttons so
that “Function” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Sound Control” is dis-
played, press ENTER.
3. Either “Master” or “Alone” will be displayed. Use the UP or DOWN
buttons to change the operating mode.
4. Press ENTER to to make your selection, or press MODE/ESC
Vizi Roller Beam 2R System Menu
Bekijk gratis de handleiding van Adj Vizi Roller Beam 2R, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Adj |
| Model | Vizi Roller Beam 2R |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 4548 MB |
